Boston Whaler 21 Justice Series Скачать руководство пользователя страница 76

Страница: 76 / 128

4-10

Section 4

Boat Systems

Battery Parallel Switch

Your boat is equipped with an emergency battery par-

allel switch. The switch is located on the control con-

sole face. You can use the emergency battery parallel

switch to connect the house battery and the engine

starting battery in parallel if the outboard engine will

not start due to low battery voltage.

The battery parallel switch controls a solenoid that

connects the two batteries. The switch is a three-posi-

tion rocker switch that is ON-OFF-ON. The center

switch position is OFF. Both the left and right switch

positions are momentarily ON when held down.

When you release the switch, it will return to the center

OFF position.

If your outboard engine will not start due to low battery

voltage, use the battery parallel switch to provide

power from the house battery.

Push and hold the battery parallel switch ON to either

the left or right position. Note this position.

Hold

the

battery parallel switch in the ON position and try to

start the engine.

If the engine does not start, release the battery parallel

switch to the OFF position. Move the battery parallel

switch to ON in the opposite direction.

Hold

the bat-

tery parallel switch in the ON position and try to start

the engine.

Содержание 21 Justice Series
































































































































Результаты поиска

Содержание 21 Justice Series

Отзывы:

Похожие инструкции для 21 Justice Series

Бренды по названию

Популярные бренды

Boston Whaler 21 Justice Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 21 Justice Series

Отзывы:

Похожие инструкции для 21 Justice Series

Бренды по названию

Популярные бренды