Boston Whaler 21 Justice Series Скачать руководство пользователя страница 35

Страница: 35 / 128

2-13

Boat Operation

Section 2

Water Pressure Gauge

The water pressure gauge displays the pressure in the

engine’s cooling system. The gauge’s unit of measure

is pounds per square inch (PSI).

The water pressure gauge is a good indicator of cool-

ing system condition. Notice the readings at various

engine RPM settings and watch for any variation.

Refer to the engine operator’s manual for PSI ranges

for your engine.

Voltmeter

The outboard engine has an alternator that charges its

starting battery when the engine is running above idle

speed. The voltmeter displays engine battery voltage

measured in DC volts (VDC).

These readings indicate that the engine battery charg-

ing system is in good condition:

• Key OFF: 0 volts

• Key ON, engine not running: 12 volts

• Engine running above idle: 14½ volts

Refer to the engine operator’s manual for additional

detailed information about the engine battery charging

system.

CAUTION

If the water pressure reading drops significantly

while the boat is on plane, stop the boat

immediately. Check the engine’s water intakes

and cooling system. If the engine is

overheating, continued operation could cause

extensive damage.

Содержание 21 Justice Series
































































































































Результаты поиска

Содержание 21 Justice Series

Отзывы:

Boston Whaler 21 Justice Series, Руководство по эксплуатации и техническому обслуживанию, Страница: 35 / 128

Результаты поиска

Содержание 21 Justice Series

Отзывы: