background image

4

5

angle/corner

mounting holes (4)

2 per side

single gang electrical

box mounting holes

speaker-to-bracket

mounting holes (2)

1 per side

single gang

electric outlet

opening

speaker cable run 

holes (2)

on top and bottom

flat mounting holes (4)

2 per side

Mounting the Bravo 20

Identify the Bracket

in its packing material, the Bravo 20’s 
mounting bracket is fitted into the back  
of the speaker. remove the tape that is 
temporarily holding the bracket to the 
speaker, and then pull the bracket away  
from the back of the speaker. Determine  
how the Bravo 20 is to be mounted to the  
wall or ceiling. it can be mounted either 
horizontally or vertically, either on an open 
section of wall, or where two or three room 
surfaces meet. refer to the illustration here to 
determine what screw holes on the Bravo 20 
bracket should be used for your application.

NOTE:  

the large rectangular hole in the 

middle of the bracket will fit a single gang 
electrical outlet to route the speaker wire 
through a conduit.

Mount the Bracket to the Wall

Decide where to mount bracket.

 

IMPORTANT:  See “Ceiling Clearance” on page 6.

Determine what mounting holes in the bracket will be used. 

mark the holes on the wall or ceiling using bracket as a template.

Drill the holes using the appropriate drill bit size to accommodate the mounting hardware that you plan to use (ie, 1⁄2-inch 
diameter to clear the toggle bolts for hollow surfaces or small enough to allow self-tapping screws in a solid surface). 

mount the bracket flat or into a corner as shown below. We recommend the use of four fasteners wherever possible. consult 
a knowledgeable installer regarding the proper hardware to use on your wall.

strip the speaker wires ends, and feed the speaker wire through the appropriate bracket opening.

connect the wire to the speaker’s terminals, taking care to maintain speaker polarity. (see “How to connect Your speakers” on 
page 2). Both the Bravo 20 and its bracket are symmetrical, so the speaker can be mounted with either its woofer or tweeter 
on top. in general, bass performance will be enhanced with the woofer as close to as many room surfaces as possible.

use up to 

16 AWG

speaker wire

feed wire

through top

or bottom

opening

Flat Mount Example

Corner Mount Example

Corner Fillers

if the Bravo 20 is being mounted in a corner, then one or both of the supplied  
corner fillers may be inserted into the slots on the back of the speaker. these 
accessories will enhance the appearance of the installation by making it appear  
that the back of Bravo 20 extends into the corner.

NOTE: 

 up to 16-gauge speaker wire will fit between the fillers and the corner.

corner filler (2)

Ceiling Clearance

if the Bravo 20 is to be mounted so that the  
top or the side of the speaker will meet a flush 
surface, either a wall (horizontally) or the ceiling 
(vertically), then measure the exact distance  
as shown here from that surface to the top or side  
of the bracket.

ceiling

or wall

 

5⁄8

 

inches (16mm)

ceiling

3

3⁄8

 

inches (86mm)

Mount the Speaker to the Bracket

remove the speaker’s grille by grasping the back of the 
cabinet in one hand, while gently pulling the grille away 
with the other hand.

align the openings in the back of the speaker with the two  
posts protruding from the bracket as shown below.

gently remove any slack in the speaker wire as you push  
the speaker firmly onto the bracket.

attach the speaker to the bracket by inserting the 
supplied screws through the holes in the front of the  
speaker and into the bracket as shown below (do not  
over-tighten the screws).

replace the grille on the speaker.

NOTE:  

the Bravo 20 is not securely attached to its bracket  

unless the screws are used.

Содержание Bravo 20






Отзывы: