Bostitch CAP1645-OF, Инструкция по эксплуатации

Страница: 14 / 53

14
15
REPAIRS
To assure product SAFETY and RELIABILITY , repairs, maintenance and adjustment should be
performed by a BOSTITCH factory service center, a BOSTITCH authorized service center or
other qualified service personnel. Always use identical replacement parts.
FULL ONE YEAR WARRANTY
B OSTITCH heavy duty industrial tools are warranted for one year from date of purchase. We
will repair, without charge, any defects due to faulty materials or workmanship. For warranty
repair information, call 1-800-556-6696 . This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by others. This warranty gives you specific
legal rights and you may have other rights which vary in certain states or provinces.
Latin America: This warranty does not apply to products sold in Latin America. For products sold
in Latin America, see country specific warranty information contained either in the packaging,
call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT (Fig. 4) : If your warning labels become illegible or are
missing, call 1-800-556-6696 for a free replacement.
WARNING
DRAIN TANK DAILY OR AFTER EVERY 4 HOURS OF US E. CONDENSATION BUILD-UP MAY CAUSE
CORROSION INSIDE TANK RESULTING IN TANK FAILURE. SEE MANUAL FOR INSPECTION PROCEDURES.
TO D RAIN TANK OPEN VALVE SLOWLY AND TILT COMPRESSOR TO EMPTY ACCUMULATED WATER.
ADVERTENCIA
DRENE EL TANQUE A DIARIO O DESPUÉS DE CADA 4 HO RAS DE USO. LA ACUMULACIÓN DE
CONDENSACIÓN PUEDE O CASIONAR CORROSIÓN DENTRO DEL TANQUE Y PROVO CAR FALLA DEL
TANQUE. CONSULTE EL MANUAL PARA CONOCER LOS PROCEDIMIENTOS DE INSPECCIÓN. PARA DRENAR EL TANQUE, ABRA LA
VÁLVULA LENTAMENTE E INCLINE EL COMPRESOR PARAELIMINAR EL AGUA ACUMULADA.
AVERTISSEMENT
RÉSE RVOIR DE VIDANGE QU OTIDIEN OU APRÈS TOUTES LES 4 HEURES D'UTILISATION.
L'HABILLAGE DE CONDENSATION PEUT CAUSER LA CORROSION À L'INTÉRIEUR DU RÉSERVOIR AYANT
POUR RÉSULTAT L'ÉCHEC DE RÉSERVOIR. VOIR LE MANUEL POUR DES PROCÉDURES D'INSPECTION. À LA VALVE
OUVERTE DE RÉSERVOIR DE VIDANGE LENTEMENT ET AU COMPRESSEUR D'INCLINAISON À L'EAU ACCUMULÉE VIDE.
WARNING HOT SURFACES
ADVERTENCIA SUPERFICIES CALIENTES
AVERTISSEMENT SURFACES CHAUDES
DO NOT OPERATE IN UPRIGHT
POSITION. UPRIGHT POSITION
IS FOR STORAGE ONLY.
NO OPERE LA HERRAMIENTA EN
POSICIÓN VERTICAL. SÓLO
ALMACENE EN ESTA POSICIÓN.
NE PAS FAIRE FONCTIONNER EN POSITION
VERTICALE. LA POSITION VERTICALE EST
RÉSERVÉE AU STOCKAGE UNIQUEMENT.
CAUTION ATENCIÓN ATTENTION
DO NOT ADJUST FACTORY SETTINGS.
TO REDUCE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER.
Pressure controls set at factory for
maximum sa fe operation.
NO HAGA CAMBIOS EN LOS AJUSTES
DE FÁBRICA. NO RETIRE LA TAPA PARA
REDUCIR EL RIESGO DE CHOQUE ELÉ CTRICO.
Los controles de presión se ajustan en la
fábrica para máxima seguridad en la ope ración.
ADVERTENCIA
WARNING
AVERTISSEMENT
FIG. 4
GLOSSARY
CFM:
Cubic feet per minute.
SCFM:
Standard cubic feet per minute; a unit of measure of air delivery.
PSI: Pounds per square inch; a unit of measure of pressure.
KPA (KILOPASCAL):
Metric pressure measurement. 1 kilopascal equal 1000 pascals.
CODE CERTIFICATION:
Products that bear one or more of the following marks: UL®, CUL, CULUS,
ETL®, CETL, CETLUS, have been evaluated by OSHA certified independent safety laboratories
and meet the applicable Standards for Safety.
*UL® is a registered trademark of Underwriters Laboratories and ETL® is a registered
trademark of Electrical Testing Laboratories.
CUT-IN PRESSURE:
While the motor is off, air tank pressure drops when accessory is used. When
the tank pressure drops to a certain low level the motor will restart automatically. The low
pressure at which the motor automatically restarts is called cut-in pressure.
CUT-OUT PRESSURE:
When an air compressor is turned on and begins to run, air pressure in the
air tank begins to build. It builds to a certain high pressure before the motor automatically shuts
off, protecting your air tank from pressure higher than its capacity. The high pressure at which
the motor shuts off is called cut-out pressure.
Branch Circuit: The circuit carrying electricity from electrical panel to outlet.