background image

17

SHUT DOWN PROCEDURE

WARNING

•  Do not ignite the torch near your body, combustible material or close to  

  regulators and cylinders.

•  Caution: the torch can become very hot during and after use, keep away  

  from skin and combustible materials, lay flat on a clean surface after use.

•  Make sure you follow the correct shutdown procedures.

•  This equipment uses compressed gas cylinders, do not disassemble    

  cylinders, puncture or incinerate.

•  Always wear the appropriate personal protective equipment when using this  

  equipment.

•  Do not disassemble the regulators, if regulator stops working, contact your  

  Bossweld agent or Bossweld directly.

•  Use only recommended parts with this equipment, altering removing or  

   using non genuine part can be very dangerous.

•  Only use fuel and oxygen cylinders that pass the AS/NZS standards,    

  compress cylinders can be very dangerous, make sure you follow  

 

  manufactures operating instructions.

MAINTENANCE

•  Only use Bossweld approved replacement parts

•  Do not use this equipment if you are unshore of any procedures outline in  

  this manuals, contact your Bossweld agent or Bossweld directly.

•  Do not use this equipment if part is damage, replace any damaged parts  

  before use.

•  Regularly inspect all parts before use, ensure valves are clean and dry  

  before connecting to the cylinders.

•  Do not disassemble any part of the equipment unless stated in this manual.

•  Check equipment for any leaks before ignition of the flame.

Содержание BRAZEN 3000





















Отзывы: