manualshive.com logo in svg

Bose Personalized Amplification System, Руководство по устранению неисправностей

Bose Personalized Amplification System - личная акустическая система для настройки звука. Помощь в устранении проблем с помощью Troubleshooting Manual, доступного для загрузки бесплатно. Скачайте свой экземпляр на manualshive.com. Получите детальное руководство для настройки звука и улучшения вашего аудио-опыта.

Поделиться
Скачать
background image

29

6. Channel 1 and 2 Line Input Signal to
Noise Ratio (Dynamic Range) Tests

6.1

 Place a 1/4” mono shorting plug into the

Amp 2 IN and Amp 3 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 2 and 3 amplifiers while
testing the channel 1 amplifier.

6.2

 On the left hand side of the input/output

panel, set the channel 1 Mic Trim control to
the 6 setting. Ensure that the Line In +20dB
gain and the Phantom Power push buttons
are not pushed in.

6.3

 Using an unbalanced 1/4” phono jack

input cable, apply a 1 kHz, -10dBV signal to
the channel 1 input.

6.4

 Reference a dB meter to the output level

at the Amp 1 OUT jack. Remove the input
signal and measure the A-Weighted output
level. It should be -80dB minimum.

6.5

 Move the shorting plug from the Amp 2

IN jack to the Amp 1 IN jack and repeat
steps 6.1 to 6.4 for the channel 2 Line input.

7. Channel 3 and 4 Line Input Gain Tests

7.1

 Place a 1/4” mono shorting plug into the

Amp 1 IN and Amp 2 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 1 and 2 amplifiers while
testing the channel 3 amplifier.

7.2

 On the left hand side of the input/output

panel, set the channel 3 Level control to the
6 setting.

7.3

 Using an unbalanced 1/4” phono jack

input cable, apply a 1 kHz, -20dBV signal to
the channel 1 input.

7.4

 Reference a dB meter to the input level.

Measure the gain output at the Bass/Amp 3
OUT jack. It should be +40.1dB + 3dB.

7.5

 Repeat steps 7.1 to 7.4 for the channel 4

Line input.

TEST PROCEDURES

8. Channel 3 and 4 Line Input Frequency
Reponse and Distortion Tests

8.1

 Place a 1/4” mono shorting plug into the

Amp 1 IN and Amp 2 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 1 and 2 amplifiers while
testing the channel 3 amplifier.

8.2

 On the left hand side of the input/output

panel, set the channel 4 Mic Trim control to
the 6 setting.

8.3

 Using an unbalanced 1/4” phono jack

input cable, apply a 1 kHz, -20dBV signal to
the channel 1 input.

8.4

 Use an 80kHz low-pass filter on your

measuring equipment. Reference a dB
meter to the input level. Measure the fre-
quency response at the Amp 1 OUT jack.
It should be 0dB + 3dB from 30Hz to 15kHz.

8.5

 Measure the Total Harmonic Distortion

(THD) level at the Amp 1 OUT jack. It should
be 0.25% max at 1kHz and 1.5% max at
15kHz.

8.6

 Repeat steps 8.1 to 8.5 for the channel

4 Line input.

9. Channel 3 and 4 Line Input Signal to
Noise Ratio (Dynamic Range) Tests

9.1

 Place a 1/4” mono shorting plug into the

Amp 1 IN and Amp 2 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 1 and 2 amplifiers while
testing the channel 3 amplifier.

9.2

 On the left hand side of the input/output

panel, set the channel 3 Level control to the
6 setting.

9.3

 Using an unbalanced 1/4” phono jack

input cable, apply a 1 kHz, -10dBV signal to
the channel 1 input.

Содержание Personalized Amplification System



















































Отзывы:

Нет отзывов

Похожие инструкции для Personalized Amplification System

Bugera 1990 INFINIUM Quick Start Manual preview
1990 INFINIUM
Бренд: Bugera Страницы: 19
Mesa/Boogie SINGLE RECTIFIER RECT-O-VERB 50 2 Series Schematics preview
SINGLE RECTIFIER RECT-O-VERB 50 2 Series
Бренд: Mesa/Boogie Страницы: 11
M2 Antenna Systems 2M-1K2 Operating Instructions Manual preview
2M-1K2
Бренд: M2 Antenna Systems Страницы: 19
Advantech ARMA-C125-CRM Installation And Operating Manual preview
ARMA-C125-CRM
Бренд: Advantech Страницы: 45
B&B Electronics Strain Gauge/Load Cell Bridge Amplifier FBDA User Manual preview
Strain Gauge/Load Cell Bridge Amplifier FBDA
Бренд: B&B Electronics Страницы: 10
bent audio TAP-X User Manual preview
TAP-X
Бренд: bent audio Страницы: 11
ELECRAFT KPA1500 Owner'S Manual preview
KPA1500
Бренд: ELECRAFT Страницы: 55
JBL MS-A5001 User Manual preview
MS-A5001
Бренд: JBL Страницы: 14
ATEN KVMP CM1164 Quick Start Manual preview
KVMP CM1164
Бренд: ATEN Страницы: 2
Laney LA15C User Manual preview
LA15C
Бренд: Laney Страницы: 26
Max 103.118 Instruction Manual preview
103.118
Бренд: Max Страницы: 16
JBL GTS100 Technical Manual preview
GTS100
Бренд: JBL Страницы: 16
TV One 1T-DA-652 Instruction Manual preview
1T-DA-652
Бренд: TV One Страницы: 10
Toa VX-2000DS ER Instruction Manual preview
VX-2000DS ER
Бренд: Toa Страницы: 16
Harman JBL DSP4086 Owner'S Manual preview
JBL DSP4086
Бренд: Harman Страницы: 10
gofanco PRO-12GSDI8P User Manual preview
PRO-12GSDI8P
Бренд: gofanco Страницы: 8
Boss Audio Systems Chaos CH600 Service Manual preview
Chaos CH600
Бренд: Boss Audio Systems Страницы: 9
Phoenix Gold Ryval V8001 Product Manual preview
Ryval V8001
Бренд: Phoenix Gold Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды