Bosch Worcester Greenstore 180 Скачать руководство пользователя страница 7

Страница: 7 / 12

TECHNICAL SPECIFICATION

Worcester Greenstore

TECHNICAL SPECIFICATIONS

Worcester Bosch Greenstore

Primary

Heating

Flow

Primary Heating Return

Return to

Solar Collector

Flow from

Solar Collector

Domestic Hot

Water Outlet

Mains Water

Inlet

Sacriﬁcial

Anode

Primary

Tank

Solar Heat

Exchanger

Solar High

Limit Stat

pocket

GT3

Heat Pump

HW Sensor

pocket

Solar

Sensor

pocket

Temperature/Pressure

Relief Valve

Solar Sensor

and

Solar High

Limit Stat

cable entry

GT3 Heat Pump

HW Sensor

cable entry

180/280 LITRE CYLINDERS WITH SOLAR COIL

Air Vent

Connecting hot water sensor GT3

Before carrying out any electrical connections, ensure that

the Heat Pump is isolated from the mains supply.

Remove the Heat Pump front cover and route the sensor

cable from the back of the Heat Pump, laying the sensor

cable onto the cable tray. Connect the sensor to terminals

GT3X on the terminal card.
Remove the cylinder front cover. Feed the sensor cable

through the grommet of the right-hand cable entry, on top

of the cylinder. Fully insert the sensor probe into the GT3

sensor pocket, as indicated on the diagram above. Replace

the cylinder front cover.

Содержание Worcester Greenstore 180













Результаты поиска

Содержание Worcester Greenstore 180

Отзывы:

Похожие инструкции для Worcester Greenstore 180

Бренды по названию

Популярные бренды

Bosch Worcester Greenstore 180, Инструкция по эксплуатации

Результаты поиска

Содержание Worcester Greenstore 180

Отзывы:

Похожие инструкции для Worcester Greenstore 180

Бренды по названию

Популярные бренды