background image

Operating the appliance       

en

17

Change the programme 

default settings

You can use the default settings or 

change them. 
To do this, repeatedly select the 

corresponding button until the required 

setting is displayed. 
The settings are activated without 

needing to be confirmed.
They are not saved when the appliance 

is switched off.
Programme default settings

 ~

 Page 15

Overview of programmes from 

~

 Page 12

Select additional programme 

settings

By selecting additional settings, you can 

better adapt the washing process to 

your items of laundry.
The settings can be selected or 

deselected depending on the 

programme progress. 
The indicator lamp for the button lights 

up if a setting is active.
The settings are not saved when the 

appliance is switched off.
Additional settings 

~

 Page 16

Overview of programmes from 

~

 Page 12

Placing laundry into the drum

:

Warning

Danger of death!

Items of laundry pretreated with 

cleaning agents that contain solvents, 

e.g. stain remover/cleaning solvent, 

may cause an explosion after being 

loaded into the washing machine.

Hand-rinse items of laundry thoroughly 

beforehand.

Notes

Mix items of laundry of varying sizes. 

Laundry items of different sizes 

distribute themselves better during 

the spin cycle. Individual items of 

laundry may lead to imbalances. 

Observe the specified maximum 

load. Overfilling has a negative 

impact on the washing result and 

promotes creasing.

1.

Place presorted items of laundry 

unfolded in the washing drum.

2.

Make sure that no items of laundry 

are trapped between the washing 

machine door and the rubber seal, 

and close the door.

The Start button indicator lamp flashes 

and the programme settings continue to 

be displayed on the display panel one 

after another. It is possible to change 

the settings.

Measure and add detergent 

and care products

Caution!

Damage to the appliance

Cleaning agents and agents for 

pretreating laundry (e.g. stain removers, 

prewash sprays, etc.) may cause 

damage if they come into contact with 

the surfaces of the washing machine. 

Do not allow these agents to come into 

contact with the surfaces of the washing 

machine. If necessary, immediately wipe 

away spray residue and other residues/

droplets with a damp cloth.

Measuring

Содержание WAK20200EG







































Отзывы: