Bosch WAB2026SZA, Руководство по эксплуатации

Страница: 8 / 8

a
‘
L
ü
Œ‹¥Ê
2
ć
7
ā
ü
Œ‹¥Ê
2
ć
I
Œ‹¥Ê
2
ć
7
1
ü
Œ‹¥Ê
2
ć
”c
Œ‹¥Ê
2
ć
G
Œ‹¥Ê
2
ć
“c
Œ‹¥Ê
2
ć
:
O
Œ‹¥Ê
Z
Œ‹¥Ê
2
ć
Ž
6
Œ‹¥Ê
2
>
L
ü @
L
ü
@
L
ü
@
L
ü
A
I
ü
B
1 ü
“c
B
ÿü
O
B
L
ć
I $
L $
$
$
~
a
ʑ
ʑ
ʑ
a
>
c >
$
11
What to do if...
ʑ Water is leaking out. – Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ No water supply.
Detergent not dispensed. – Start/ Pause
$
not selected?
– Tap not turned on?
– Filter blocked? Clean the filter
a page 10
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened. – Safety function active. Programme stopped? a page 4 .
– - - - - (Rinse stop = no final spin) selected? a page 3,4.
ʑ
Programme does not start. – Start /Pause
$
or Ready in time selected?
– Washing machine door closed?
– Childproof lock active? Deactivating
a
page 5.
ʑ Detergent solution is not
drained. – - - - - (Rinse stop = no final spin) selected?
a page 3, 4.
– Clean the detergent solution pump a page 10.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum. – Not a fault - water below the visible area.
ʑ
Spin result not satisfactory.
Laundry wet/too damp. – Not a fault - the imbalance monitoring system has interrupted the spin
because the laundry is unevenly distributed.
Distribute large and small items of laundry evenly in the drum.
– Speed selected too low?
a
page 5 .
ʑ
The programme duration
changes during the wash
cycle. – Not a fault - the programme cycle is optimised for the particular
washing process. This can cause changes in the programme duration
on the display panel.
ʑ Spin cycle performed
several times. – Not a fault - unbalanced-load detection system is adjusting the
imbalance.
ʑ Residual water in the
0
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary
a page 10 .
ʑ
Odour formation in the
washing machine. – Run programme
L
Cottons 90 °C without laundry. Use standard
detergent.
ʑ
Status display
t
flashing.
Appliance has detected a
detergent overload.
– Too much detergent used?
Mix one tablespoonful of fabric softener with ½ litre water and pour
into compartment
II (Not for outdoor fabrics, sportswear fabrics or
those made with down.)
– Reduce the detergent dosage for the next wash cycle .
ʑ
Loud noises, vibrations and
“wandering” during the
spin cycle. – Are the appliance feet fixed?
Secure appliance feet
a
Installation instructions .
– Transportation safety devices removed?
Remove transportation safety devices a Installation instructions .
ʑ
Display panel/indicator
lamps do not function
during operation. – Power cut?
– Circuit breakers tripped? Switch the circuit breakers back on or
replace.
– If the fault occurs repeatedly, call the after-sales service.
ʑ Programme sequence
longer than usual. – Not a fault - unbalanced-load detection system is adjusting the
imbalance by repeatedly redistributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse
cycle.
ʑ
There are detergent
residues on the laundry. – Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Select Rinse
2
or brush down the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service
a
Installation instructions.
en operating instructions
Washing machine
WAB2026SZA