Bosch TR2000TF 200 T, Инструкция по установке и эксплуатации

Страница: 12 / 20

Maintenance instructions
TR2000TF – 6 720 875 992 (2017/07) 12
• Set a higher temperature with the temperature selector switch 1 if
you frequently need to reheat water during the peak period.
As a result, you will have a larger volume of mixed water.
• Rotate the temperature selector switch 1 to position “•” if the floor-
standing water heater will not be heated for a prolonged period.
This setting protects the appliance from freezing.
This does not apply to the fittings and pipes in the cold-water inlet!
4.5 Checking the safety valve
During the heating process, expansion water must drip out of the safety
valve outlet
3 .
For reasons of safety the outlet must not be blocked.
• Check that the safety valve is functioning properly at least once
a month.
• Rotate ventilation screw 4 until the valve opens and a powerful jet of
water comes out of the outlet 3 .
• Close the valve again with the ventilation screw.
• If the safety valve does not function as described, rotate the
temperature selector switch to position “•” and contact a qualified
professional.
4.6 Saving energy
The appliance operates particularly economically at low temperatures.
Therefore, only set the temperature which you require.
The floor-standing water heater operates most economically in position
“E” (approx. 60 °C), even when large amounts of hot-water are required.
At higher water temperatures, the appliance calcifies at an increased
rate, resulting in greater heat losses!
4.7 Decalcifying
• Inspect the fittings regularly for lime scale deposits and descale with
commercially available descaling agents.
• Actuate the safety valve regularly to remove the lime scale (see
“Checking the safety valve”).
The level of lime scale deposited from the water is increased or reduced
at higher temperatures depending on the local water quality (hardness
level I/II/III; soft, medium or hard). It is deposited on the interior of the
water tank and on the heating element as boiler scale and influences the
service life of the appliance.
The appliance must therefore be checked and decalcified regularly by
a qualified professional.
Please schedule your first and/or next maintenance visit (inspection of
the protection anode and descaling) with your qualified specialist.
Maintenance work may only be carried out by a qualified
professional.
Improper repairs may put the user in extreme danger.
4.8 Cleaning
• Simply wipe the appliance with a damp cloth. Do not use acidic or
abrasive cleaning materials.
4.9 Customer Service
• In the event of a malfunction, unplug the appliance from the power
supply (pull out the fuse or activate the circuit breaker) and contact
customer service.
Details can be obtained from a customer service centre regarding your
nearest customer service centre or authorised repair shop.
• We ask you to always provide the BOSCH serial number (SNR/TTNR)
of your appliance when calling in a customer service engineer.
5 Maintenance instructions
CAUTION:
▶
Maintenance work must only be carried out by a qualified
professional, pursuant to VD E0700 or local regulations.
• The appliance must be isolated from the power supply in all poles.
5.1 Decalcifying
Do not use a decalcifying pump. This would decalcify the heating flange
but would damage the protective anode and the interior wall of the tank.
Procedure:
• Disconnect the floor-standing water heater from the power supply.
• Remove the switchroom cap.
• Disconnect the heating flange and remove.
• Decalcify the heating flange.
• Remove loose pieces of lime from the floor-standing water heater.
• Fit the heating flange and connect in accordance with the circuit
diagram.
• Fit the switchroom cap.
5.2 Checking the protective anode
The protective anode must be removed prior to checking.
It is situated next to the hot-water outlet nozzle and is covered by the
thermal insulation (recognizable by a protrusion).
• Unzip the protective jacket. Cut out the thermal insulation with
a knife.
• Screw out the protective anode and check.
If the protective anode is used up, it must be replaced with a new one.
If there is insufficient space to install a pole anode, install a chain anode.
The protective anode must have a good metallic conduction with the
floor-standing water heater. Cover the screwed connection of the anode
with the piece of thermal insulation material which was previously cut
out.
• Zip up the protective jacket.
Note: The protective anode, located in the floor-standing water heater,
must be checked for the first time after two years and replaced if
necessary. The qualified professional is familiar with the local water
quality and will specify when the next maintenance check should be
carried out.
5.2.1 Safety valve
• Vent the safety valve until the full water jet is flowing out.
• Close the safety valve after carrying out the check.
Safety equipment (Fig. 9)
5 Thermal cut-out
6 Corrosion protection anode resistor
7 Heating flange
8 Reset button
The thermostat and thermal cut-out are located together in the heating
flange. If the thermal cutout disconnects the appliance due to
a malfunction, the whole unit must always be replaced. The cause of the
malfunction must be eliminated by a qualified professional.
The heating flange is connected with the tank via the corrosion protection
anode resistor. The corrosion protection anode resistor serves to equalise
electrical potential differences and prevents current-related corrosion to
the heating elements. The anode resistor is not to be damaged or removed
during servicing (for mounting position, refer to figure).