Bosch TA025 Скачать руководство пользователя страница 27

Страница: 27 / 28

6 720 220 046

Revised 03-11 Subject to change without prior notice

TA Series

Troubleshooting

Insufficient

cooling or

heating

Unit undersized

Recalculate heating and or cooling loads. If excessive, possibly adding

insulation and shading will rectify the problem

Loss of conditioned

air by leakage

Check for leaks in duct work or introduction of ambient air through

doors or windows

Airflow

Lack of adequate air flow or improper distribution of air. Replace dirty

filter

Refrigerant charge

Low on refrigerant charge causing inefficient operation

Compressor

Check for defective compressor. If discharge is too low and suction

pressure is too high, compressor is not pumping properly. Replace

compressor.

Reversing Valve

Defective reversing valve creating bypass of refrigerant from discharge

of suction side of compressor. Replace reversing valve

Operating

pressures

Compare unit operation pressures to the pressure/temperature chart

for the unit.

TXV

Check TXV for possible restriction or defect. Replace if necessary.

Moisture,

noncondensables

The refrigerant system may be contaminated with moisture or

noncondensables. Reclaim refrigerant, replace filter dryer, evacuate the

refrigerant system, and recharge with factory recommended charge.

Содержание TA025




























Результаты поиска

Содержание TA025

Отзывы:

Похожие инструкции для TA025

Бренды по названию

Популярные бренды

Bosch TA025, Руководство по установке и обслуживанию

Результаты поиска

Содержание TA025

Отзывы:

Похожие инструкции для TA025

Бренды по названию

Популярные бренды