Bosch TA025 Скачать руководство пользователя

Страница: 26 / 28

Subject to change without prior notice Revised 03-11

6 720 220 046

26 TA Series

Troubleshooting

TroubleSHooTInG

Problem

Possible Cause

Checks and Corrections

Entire unit

does not run

Power Supply Off

Apply power, close disconnect

Blown Fuse

Replace fuse or reset circuit breaker. Check for correct fuses

Voltage Supply Low

If voltage is below minimum voltage specified on unit data plate,

contact local power company.

Thermostat

Set the fan to “ON”, the fan should run. Set thermostat to “COOL” and

lowest temperature setting, the unit should run in the cooling mode

(reversing valve energized). Set unit to “HEAT” and the highest tempera-

ture setting, the unit should run in the heating mode. If neither the blower

or compressor run in all three cases, the thermostat could be miswired or

faulty.To ensure miswired or faulty thermostat verify 24 volts is available

on the condensing section low voltage terminal strip between “R” and

“C”, “Y” and “C”, and “O” and “C”. If the blower does not operate, verify

24 volts between terminals “G” and “C” in the air handler. Replace the

thermostat if defective.

Blower

operates but

compressor

does not

Thermostat

Check setting, calibration, and wiring

Wiring

Check for loose or broken wires at compressor, capacitor, or contactor.

Safety Controls

Check UPM board red default L.E.D. for Blink Code

Compressor

overload open

If the compressor is cool and the overload will not reset, replace compres-

sor.

Compressor motor

grounded

Internal winding grounded to the compressor shell. Replace compressor.

If compressor burnout, install suction filter dryer.

Compressor

windings Open

After compressor has cooled, check continuity of the compressor

windings. If the windings are open, replace the compressor

Unit off on

high pressure

control

Discharge pressure

too high

In “COOLING” mode: Lack of or inadequate water flow. Entering water

temperature is too warm. Scaled or plugged condenser.

In “HEATING” mode: Lack of or inadequate air flow. Blower inoperative,

clogged filter or restrictions in duct work

Refrigerant charge

The unit is overcharged with refrigerant. Reclaim refrigerant, evacuate

and recharge with factor recommended charge.

High pressure

Check for defective or improperly calibrated high pressure switch.

Unit off on

low pressure

control

Suction pressure

too low

In “COOLING” mode: Lack of or inadequate air flow. Entering

air temperature is too cold. Blower inoperative, clogged filter or

restrictions in duct work

In “HEATING” mode: Lack of or inadequate water flow. Entering water

temperature is too cold. Scaled or plugged condenser.

Refrigerant charge

The unit is low on refrigerant. Check for refrigerant leak, repair,

evacuate and recharge with factory recommended charge.

Low pressure

switch

Check for defective or improperly calibrated low pressure switch.

Unit short

cycles

Unit oversized

Recalculate heating and or cooling loads.

Thermostat

Thermostat installed near a supply air grill; relocate thermostat.

Readjust heat anticipator.

Wiring and controls Check for defective or improperly calibrated low pressure switch.

Содержание TA025




























Результаты поиска

Содержание TA025

Отзывы:

Похожие инструкции для TA025

Бренды по названию

Популярные бренды

Bosch TA025, Руководство по установке и обслуживанию

Результаты поиска

Содержание TA025

Отзывы:

Похожие инструкции для TA025

Бренды по названию

Популярные бренды