Bosch SK Series Скачать руководство пользователя | Manualshive

Страница: 36 / 38

background image

en

Installation and connection

36

Electrical connection

ヽ

Connect the appliance to an
alternating current only, ranging from
220 V to 240 V and 50 Hz or 60 Hz
via a correctly installed socket with
protective earth conductor. See
rating plate for required fusing

1b

.

ヽ

The socket must be near
the appliance and freely accessible
following installation.
If the plug is not freely accessible, an
allpole disconnector with a contact
opening of at least 3 mm must be
fitted on the installation side
to satisfy the relevant safety
instructions.

ヽ

The connection may be modified by
technicians only.

ヽ

A power cord extension may be
purchased from customer service
only.

ヽ

Use only a residual current operated
circuit-breaker which features
the symbol

‚

. Only this extension

guarantees compliance with
the currently valid regulations.

ヽ

The appliance features a water
damage protection system. Please
note the system will not function

unless

the power supply

is connected.

Removing the appliance

Also observe
the sequence of worksteps here.

1.

Disconnect the appliance from
the power supply.

2.

Turn off the water supply.

3.

Undo the waste water and drinking
water connection.

4.

Pull out the appliance, carefully
pulling the hose behind.

Transportation

Empty the dishwasher and secure loose
parts.

Drain the appliance according to the
following steps:
1.

Turn on the tap.

2.

Close the door.

3.

Switch on ON/OFF switch

(

.

4.

Select programme with the highest
temperature.
The expected programme duration is
indicated on the numerical display

h

.

5.

Press START button

H

.

Programme sequence starts.

6.

After approx. 4 minutes press the
START button

H

until

‹

:

‹‚

is

indicated on the digital display.
After approx. 1 min

‹

:

‹‹

is indicated

on the digital display .

7.

Switch off ON/OFF switch

(

.

8.

Turn off the tap, disconnect supply
hose and drain water.

Transport appliance upright only.
(This prevents residual water from
running into the machine control and
damaging the programme sequence.)

Protection against frost

Protection against frost (Emptying the appliance)

If the appliance is in a room where there
is a risk of frost (e.g. holiday home),
empty the appliance completely (see
Transportation).

6XEMHFWWRFKDQJHV

«
...
34
35
36
37
38
»

Содержание SK Series







































Отзывы:

Нет отзывов

Похожие инструкции для SK Series

Бренд: Haier Страницы: 12

Бренд: Jackson Страницы: 48

Бренд: Haier Страницы: 8

Бренд: White-Westinghouse Страницы: 10

Бренд: Blomberg Страницы: 20

Бренд: ZANKER Страницы: 19

Бренд: Indesit Страницы: 16

Бренд: Frigidaire Страницы: 13

Бренд: Frigidaire Страницы: 6

Бренд: Frigidaire Страницы: 20

Бренд: Frigidaire Страницы: 16

Бренд: Frigidaire Страницы: 16

Бренд: Frigidaire Страницы: 20

Бренд: Frigidaire Страницы: 16

Бренд: Frigidaire Страницы: 16

Бренд: Frigidaire Страницы: 16

Бренд: Frigidaire Страницы: 16

Бренд: Frigidaire Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды