Bosch RM2-DP12 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 36

background image

1070 072 449-102 (01.12) GB

Technical Data

9-1

9 Technical

Data

Technical Data

RM2-DP12 Module

Complies fully with the requirements of

IEC1131-2
DIN VDE 0110
DIN EN 60204-1 (as per VDE 0113)

Weight:

270 g approximately

Dimensions (W x H x D):

30 x 182 x 115 mm

Front panel: :

Module width 1

Storage temperature:

-25...+70°C as per IEC 1131-2

Operating temperature:

0...55°C

as per IEC 1131-2

Slot:

The module must only be operated on slot 1 in the
mounting rack.

Power Supply:

24 VDC (-15...+20%)

Power failures of up to 10 ms with nominal
voltage, with a 1 s break in between as per
IEC 1131-2.

Current input:

1.35 A max.

Discharge capacity:

24 V against protective earth:

4.7 nF

0 V against protective earth:

4.7 nF

Internal supply for I/O modules:

7.5 V (+/- 5%) / 1.2 A max.

Supply of bus interface (X71):

P5VISO/GNDISO (+/- 5%) / externally 100 mA
max. RS485, electrically isolated.

Degree of protection:

IP20 as per DIN VDE 0470-1
incorporated in the housing.

Class of protection:

1 as per VDE 0106 T1 or VDE 0160 (IEC 536)

Insulation test:

350 VAC
500 VDC

Atmospheric pressure:

Operation up to 2000 m above sea level as per
IEC 1131-2

Humidity rating:

RH-2; 5%...95% as per IEC 1131-2.
F as per DIN 40040

Condensation not permissible.

Corrosion / chemical resistance:

The ambient air must be free of elevated concen-
trations of acids, alkali, corrosive agents, salt,
metal vapors or other electrically conductive
pollutants.

Dirt resistance:

Degree of contamination 2 as per EN 1131-2

The RM2-DP12 module requires a dustfree
environment. The housing and compartments in
which the mounting rack is located must comply
with the minimum degree of protection IP54 as per
DIN VDE 0470-1.

Transportability:

Height of fall in packaging 1.0 m as per IEC 1131-2

«
...
32
33
34
35
36
»

Содержание RM2-DP12





































Отзывы:

Нет отзывов

Похожие инструкции для RM2-DP12

Бренд: Gardigo Страницы: 8

Бренд: Gardigo Страницы: 19

Бренд: Nabco Страницы: 35

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Neles Страницы: 12

Бренд: olympia electronics Страницы: 10

Бренд: Samson Страницы: 8

Бренд: Samson Страницы: 60

Бренд: Samson Страницы: 40

Бренд: Ultraflex Страницы: 7

Бренд: bihl+Wiedemann Страницы: 16

Бренд: oventrop Страницы: 64

Бренд: Colorbeam Страницы: 12

Бренд: Kramer Страницы: 60

Бренд: Samson Страницы: 32

Бренд: Bartec Страницы: 52

SR-ZV9002T4-CCT-RU

Бренд: Z-Wave Alliance Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды