Bosch rexroth SB24 Скачать руководство пользователя страница 64

Страница: 64 / 78

64/78 Commissioning

Bosch Rexroth AG, Control block SB24/34, RE 66170-B/2019-05-15

8.3 Air bleeding

8.3.1 Air bleeding at control block/control block segment

NOTICE!

Short circuits may only be established at working ports at the same

directional valve. Rinsing of the hydraulic lines in the housing is only be possible
by establishing short circuits.

▶

Establish short circuits between the individual directional valve with the working
ports

and

, e.g. by means of a hydraulic line.

▶

At EHR control valves, working port

must be plugged.

Fig. 6: Control block examples with threaded port and hydraulic line

▶

Start air bleeding with the directional valve with the maximum distance to port

– For SB control valves, refer to chapter 8.3.2

– For control valves with EHS, refer to chapter 8.3.3

– For EHR control valves, refer to chapter 8.3.4

8.3.2 Air bleeding at SB control valves

The hydraulic fluid flow via ports

and

must be applied. The two consumer

ports

and

must be connected, e.g. by means of a hydraulic line.

Apply a hydraulic fluid flow through the directional valve for at least 20 seconds
and slowly set the valve spool from 0 or neutral position to the fine control range
of spool position

and

Repeat this process several times.

Switch spool positions

and

several times to maximum position.

Содержание rexroth SB24















































































Результаты поиска

Содержание rexroth SB24

Отзывы:

Похожие инструкции для rexroth SB24

Бренды по названию

Популярные бренды

Bosch rexroth SB24, Инструкция по эксплуатации

Результаты поиска

Содержание rexroth SB24

Отзывы:

Похожие инструкции для rexroth SB24

Бренды по названию

Популярные бренды