background image

Personal injury and property damage during in-

stallation work!

WARNING

Do not work on unsecured and operating machines.

Before working, secure the machine against accidental movements and

against unauthorized operation.

Secure the motor and the supply lines against dropping or movements before

unfastening the mechanical connections.

Combustions via hot surface with temperatures

over 60 ℃

CAUTION

Let the motor cool down, before maintenance. The thermal time constant stated

in the technical data is a measure for the cooling time. A cooling time up to 140

minutes can be necessary!
Use safety gloves.
Do not work on hot surfaces.

In the case of malfunctions, maintenance, or disassembly of the motors, pro-

ceed as follows:

1. Use the control commands to decelerate the drive to a controlled stand-

still.

2. Switch off the power and control voltage of the controller.
3. Switch off the main switch of the machine.
4. Secure the machine against accidental movements and against unauthor-

ized operation.

5. Wait for the cooldown times of the motor and the discharge time of the

electrical systems to elapse.

6. Disconnect all electrical connections.
7. Before disassembling the motor and the supply lines, secure them against

dropping or movements. Subsequently, disconnect the mechanical connec-

tions.

1.13.1  Maintenance

Increase availability with regular preventive maintenance measures. Comply with

the machine manufacturer's instructions in the machine maintenance plan and

the maintenance measures and intervals on the motor described below.

MSK Motors Operation For Potentially

Explosive Areas  

17/27

Operating instructions

R911323850_Edition 05 Bosch Rexroth AG

Содержание Rexroth MSK030-NSNN Series

















































Отзывы: