Bosch Rexroth IndraControl XFE 01.1 Series Скачать руководство пользователя страница 12

Страница: 12 / 36

12 / 36

IndraControl XFE 01.1

Standards used

Bosch Rexroth AG

R911345570, Edition 06

NOTICE

Electronic damage due to polarity reversal or due to a nominal current that is

too low
The power supply unit has to be able to provide the quadruple nominal

current of the maximum current consumption to ensure a reliable triggering in

case of a failure.

7.2.1

Electrical isolation and isolation of the voltage ranges

Profibus extension module

V supply with FE to XF8

DC 1200 V, 1 min.

RT Ethernet extension module

V supply with FE to XF40

DC 1200 V, 1 min.

V supply with FE to XF41

DC 1200 V, 1 min.

XF40 to XF41

DC 1200 V, 1 min.

Sercos extension module

V supply with FE to XF3

DC 1200 V, 1 min.

V supply with FE to XF4

DC 1200 V, 1 min.

XF3 to XF4

DC 1200 V, 1 min.

CAN extension module

V supply to XF70

DC 1200 V, 1 min.

V supply to XF71

DC 1200 V, 1 min.

V supply to FE

DC 1200 V, 1 min.

XF70 to FE

DC 1200 V, 1 min.

XF71 to FE

DC 1200 V, 1 min.

XF70 to XF71

DC 1200 V, 1 min.

Standards

8.1

General information

The products have been developed according to the German editions of the standards published at the

time of product engineering.

8.2

Standards used

Table 6: Standards used

Standard

Meaning

Edition

IEC 60204-1

Electrical equipment of machines

2007

IEC 61131-2

Programmable logic controllers

2008

Содержание Rexroth IndraControl XFE 01.1 Series





































Результаты поиска

Содержание Rexroth IndraControl XFE 01.1 Series

Отзывы:

Похожие инструкции для Rexroth IndraControl XFE 01.1 Series

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl XFE 01.1 Series, Руководство по эксплуатации

Результаты поиска

Содержание Rexroth IndraControl XFE 01.1 Series

Отзывы:

Похожие инструкции для Rexroth IndraControl XFE 01.1 Series

Бренды по названию

Популярные бренды