manualshive.com logo in svg

Bosch rexroth HyDrotrAC GFt, Руководство по эксплуатации

Поделиться
Скачать
Bosch rexroth HyDrotrAC GFt Скачать руководство пользователя страница 62

62/64 

HyDrotrAC GFt >130 knm  

 | Troubleshooting and fault correction

Bosch Rexroth AG, Issue 10.2019, RE 79094

 

table 7:  Malfunction table of the HyDrotrAC GFt

Malfunction

possible cause

remedy

Changed gearbox noises

Damaged gears

Notify Customer Service.

Check toothed components for 

flaws such as pittings.

Let the damaged parts be 

replaced by Rexroth Service.

Bearing play

Notify the Rexroth Service.

Bearing play

Noises

Gearbox fastening has 

become loose

Tighten screws with the 

required tightening torque.

The operating temperature 

is substantially higher than 

normal

The oil level is too high or 

too low

Allow the planetary gearbox to 

cool down to approx. 50°C.

Check the oil filling level.

If required, fill with lubricating 

oil or drain off lubricating oil if 

oil level is too high.

The lubricating oil is too old 

or badly contaminated

Check in the operating 

instructions of the system, 

machine or vehicle when the 

last oil change took place, if 

appropriate proceed to an oil 

change. Proceed as described in 

chapter 10.2 “Inspection”.

Leaking oil

Defective output seal.

Check seals as far as possible, 

replace if necessary.

If the leak cannot be eliminated, 

Rexroth Service must be 

notified.

Seals on partition seams or 

on the locking screws are 

defective

Lubricating oil is foaming

Incompatibility of the filled 

in lubricating oil with the oil 

remains or the preservation 

oil of the planetary gearbox.

Replace the lubricating oil and 

rinse with appropriate purging 

oil.

Decreasing or non-existent 

brake action

Thermal overload of the 

multiple-disk brake

Contact the Rexroth Service.

Let trained staff or Rexroth 

Service employees carry out 

an inspection on the multiple-

disk brake. Replace the disks, 

springs and sealing elements 

per axle.

If the malfunction occurrences cannot be eliminated, please contact one of the 

contact addresses indicated on 

www.boschrexroth.com

 or in the address 

directory in appendix A “Address directory” of the material number-specific 

operating instructions.

CorreCtion Copy 1 |17.10.2019 | onLy For internAL USe

Содержание rexroth HyDrotrAC GFt

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды