Bosch rexroth HQ 2/U-H страница 55 Скачать руководство пользователя

Страница: 55 / 72

10.4.4 Replacing the motor and/or gear

Fig. 42:

SW13

=22 Nm

=5 Nm

SW8

=5 Nm

SW4

=5 Nm

Antiseize

562 240-27

Loctite 243

Replacing the motor and/or gear

Please note:

• The end faces of the motor and gear must be undamaged.

• The gear hub comes lubricated with anti-seize lubricant.

• If only the motor is to be replaced: grease the gear hub with anti-seize.

• Do

not tilt the motor, and make sure it has the necessary clearance area for

installation.

• Install the motor in the proper position (terminal box) and connect it to the gear.

If the motor is not in the proper position: do

NOT rotate the motor. Disconnect the

motor from the gear and reconnect it.

It is possible to replace the

motor and/or the gear when

the HQ 2/U-H is installed in

the section.

If only the motor is to be

removed, start with pos. 5.

Remove the roller chain

(see page 53).

Remove the motor-gear

combination.

Remove the hanger from

the ﬂ ange (G).

Remove the ﬂ ange (G)

from the gear.

Loosen the hexagon

screws on the gear

ﬂ ange.

Disconnect the defective

gear from the motor.

Remove the yellow

protective cap (X) from

the motor shaft of the

new motor.

Grease the motor shaft.



Install the motor.

Install the motor-gear

combination in reverse

order.

Check the tension of the

roller chains (see page

53) and correct the

tension if necessary.

Maintenance and repair

55/72

3 842 562 241/2019-04, MIT: HQ 2/U-H,

Bosch Rexroth AG

GLISH

Содержание rexroth HQ 2/U-H









































































Результаты поиска

Содержание rexroth HQ 2/U-H

Отзывы:

Похожие инструкции для rexroth HQ 2/U-H

Бренды по названию

Популярные бренды

Bosch rexroth HQ 2/U-H, Руководство по сборке

Результаты поиска

Содержание rexroth HQ 2/U-H

Отзывы:

Похожие инструкции для rexroth HQ 2/U-H

Бренды по названию

Популярные бренды