Bosch Rexroth HMU05.1N Series страница 119 Скачать руководство пользователя

Страница: 119 / 410

4.7

Acceptance tests and approvals

Declaration of conformity

Declarations of conformity confirm that the components comply with the valid

EN standards and EC directives. If required, our sales representative can

provide you with the declarations of conformity for components.

Drive controllers,
Supply units

Motors

CE conformity regarding

Low-Voltage Directive

EN 61800-5-1:2007

EN 60034-1:2010+Cor.:2010
EN 60034-5:2001+A1:2007

CE conformity regarding

EMC product standard

EN 61800-3:2004 + A1:2012

Tab. 4-23:

CE - applied standards

C-UL-US listing

The components are listed by UL (Underwriters Laboratories Inc.®).
Proof of certification can be found online:

www.ul.com/database

Under "UL File Number" enter the file number or under "Company Name" en‐

ter the company name "Bosch Rexroth AG".

●

UL standard: 61800-5-1

●

CSA

standard:

Canadian

Standard

CSA C22.2 No. 274-13

Company Name
BOSCH REXROTH ELECTRIC DRIVES & CON‐

TROLS GMBH
Category Name:
Power Conversion Equipment
File numbers
Rexroth IndraDrive ML components (HMU05, HNA05,

HNC05, HNF05, HNL05, HML05, HLL05, HPC01):
●

E134201

Tab. 4-24:

C-UL listing

UL ratings
When using the component in the scope of CSA / UL, observe the

UL ratings for each component.
Make sure that the indicated SCCR short-circuit rating is not ex‐

ceeded, e.g., by using appropriate fuses in the mains connection

of the supply unit.

UL wiring material
In the scope of CSA / UL, use copper 60/75 °C only; class 1 or

equivalent only.

DOK-INDRV*-HXX05******-PR02-EN-P

Bosch Rexroth AG

117/407

Rexroth IndraDrive ML Drive Systems with HMU05

Combining the individual components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды