Bosch Rexroth CytroMotion Скачать руководство пользователя страница 29

Страница: 29 / 60

29 / 60

Self-contained axis

Assembling the self-contained axis

Bosch Rexroth AG

RE62290-B, 05.22

Table 8: Cable sets and mating connectors for pressure transducers

Designation

Version

Material number Data sheet /

standard

Cable sets, 4-pole

M12 x 1, straight, 2.0 m

R900773031

08006

M12 x 1, straight, 5.0 m

R900779498

Mating connectors, 4-pole M12 x 1, straight, PG 7

R900773042

Table 9: Mating connector for position measurement system

Designation

Version

Material number Data sheet /

standard

MATING CONNECTOR 7P

STC09131D07

M16, 7-pole, straight

R900079551

For dimensions,

see

⮫

data sheet

Table 10: Mounting kit

Designation

Version

Material number Data sheet /

standard

ASSEMBLY MKT-1X/

040M10/10.9ZN

for “040/028” version
8x M10x40/120-10.9-FLZN/NC/

480H/C

R901564086

ISO4762

ASSEMBLY MKT-1X/

050M120/10.9ZN

for “050/036” version
8x M12x40/120-10.9-FLZN/NC/

480H/C

R901564085

ASSEMBLY MKT-1X/

063M12/10.9ZN

for “063/045” version
8x M12x45/125-10.9-FLZN/NC/

480H/C

R901564084

ASSEMBLY MKT-1X/

080M16/10.9ZN

for “080/056” version
8x M16x55/135-10.9-FLZN/NC/

480H/C

R901564083

Screw length for minimum screw-in depth 1.2 x d

7.5

Assembling the self-contained axis

7.5.1

Preparation for assembly

Check the scope of delivery for completeness and transport damage.

Compare the material number with the details in the order confirmation.

If the material numbers or designations of the self-contained axis do not match

those on the order confirmation, contact Bosch Rexroth Service for clarifica-

tion, see

⮫

Chapter 16.1 Service and support on page 55

7.5.2

Mechanical installation

WARNING

Incorrect mounting! Insufficient fixation or insufficient

stability may cause the self-contained axis to become

loose and fall down. Consequently, hydraulic fluid may

leak and lead to personal injuries and/or damage to

property. Very heavy self-contained axes may bruise or

kill persons.

−

Completely assemble the self-contained axis

according to the assembly specifications using suit-

able assembly aids.

Содержание Rexroth CytroMotion





























































Результаты поиска

Содержание Rexroth CytroMotion

Отзывы:

Похожие инструкции для Rexroth CytroMotion

Бренды по названию

Популярные бренды

Bosch Rexroth CytroMotion, Руководство по эксплуатации

Результаты поиска

Содержание Rexroth CytroMotion

Отзывы:

Похожие инструкции для Rexroth CytroMotion

Бренды по названию

Популярные бренды