Bosch rexroth CytroForce-M Скачать руководство пользователя страница 46

Страница: 46 / 85

46 / 85

Servo-hydraulic actuator
Software commissioning

Bosch Rexroth AG

RE62270-B, 01.21

Check for functionality and correct connection of valve technology, sen-

sors, position measuring system, etc.

Conducting a system validation

🡆

Target/actual comparison of the requirements list

🡆

Compliance with voltage drops

🡆

Power measurement to determine the electrical connection values in

normal and peak load operation.

🡆

Creation of a “good condition fingerprint” based on the measured sig-

nals, e.g. noise measurement

The stepwise re-commissioning of the servo-hydraulic actuator after malfunc-

tion was rectified must always be agreed with Bosch Rexroth.

8.2

Software commissioning

General
For commissioning the servo-hydraulic actuator no special activities are

required, since all the necessary settings of hardware and software were made

in the factory.
However, when a component is to be replaced it may be necessary to make

some settings at the drive controller.

Requirements
The following components are required for commissioning:

●

Servo-hydraulic actuator completely connected and supplied

●

Drive controller firmware MPx20VRS

●

microSD card, which is inserted in the card slot of the drive controller

●

PFC software (see commissioning instructions “Rexroth Sytronix SvP 7020

PFC Variable-Speed Positioning of Hydraulic Axes”, R. 62313-FK,

⮫

Chapter 1.2 “Required and supplementary documentation” on page 5).

●

Standard Ethernet cable

●

PC with free Ethernet port

●

Current version of IndraWorks Ds (IndraWorks Ds 14VRS or above)

It is possible to backup parameters. For information on reading parameter

backups, please see the Application Manual of MPx-20,

⮫

Chapter 1.2

“Required and supplementary documentation” on page 5.
In the event of a fault, a further parameter backup has to be made. A compar-

ison with the parameter set stored last (during operation) simplifies trouble-

shooting and helps you to quickly restore the configuration.

Procedure
How to proceed for commissioning of the drive controller is described in detail

in commissioning instructions "Rexroth Sytronix SvP 7020 PFC Variable-Speed

Positioning of Hydraulic Axes, R.62313-FK",

⮫

Chapter 1.2 “Required and sup-

plementary documentation” on page 5".
The following graphic roughly represents the individual commissioning steps:

Содержание rexroth CytroForce-M






















































































Результаты поиска

Содержание rexroth CytroForce-M

Отзывы:

Похожие инструкции для rexroth CytroForce-M

Бренды по названию

Популярные бренды

Bosch rexroth CytroForce-M, Руководство по эксплуатации

Результаты поиска

Содержание rexroth CytroForce-M

Отзывы:

Похожие инструкции для rexroth CytroForce-M

Бренды по названию

Популярные бренды