Bosch Rexroth CIMS Mk IV Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 60

background image

F 037 300 069 (2013.05.21)

7

2.3.2.

ATEX

PROTECTION TYPE AND MARKING

II 2 G Ex d IIB T4 Gb

This means the sensor is designed for use in a non-mining application and a category 2
surrounding (gas, zone 1). Gas group IIB such as ethylene and petrol fumes is applicable and the
maximum temperature of the sensor housing will not exceed 135 ºC (Temperature class T4).
The ATEX approved version is recognizable by the applicable Ex code as stated above that is
engraved in the housing cover of the CIMS Mk IV.
Compliance with the Essential Health and Safety requirements has been assured by compliance
with:
DIN EN 60079-0: 2010-03 DIN EN 60079-1: 2008-04

During installation and maintenance, the CIMS and / or the Ex cable gland needs to be opened or
removed. In that situation the sensor is not Ex approved!

Marking:
Manufacturer

Exepd

GmbH,

D-97922

Lauda

Type

CIMS Mk IV

Ex-Marking

II 2G Ex d IIB T4 Gb

CE and no. notified body

CE 0123

EC-Type-Certificate

BVS 12 ATEX E 111 X

Nominal voltage

24 V DC (155 mA)

Connecting thread of cable gland

G1/2”

Ambient

temperature

-20°C

≤

Ta

≤

+70°C

Before starting up read handbook

The serial no. is marked on the housing cover, Intermediate piece and the housing base.

Special conditions for safe use:
1. The ATEX-approved CIMS Mk IV sensor is suitable for use in an environment with an ambient
temperature range from -20 °C to +70 °C.
2. Repairing the sensor is not permitted. A defect CIMS Mk IV has to be replaced by trained
personal.
3. The ATEX-approved CIMS Mk IV is only frameproof with a suitable Ex d cable entry system, see
Section 4.2.5.2.
4.

The cable gland and the cable have to be suitable for max. operation temperature of 80°C.

5. Inspection and maintenance requirements are given in Section 2.3.6.

Mechanical strength: Impact energy max. 7 Nm

2.3.3.

A

SSEMBLY

Only authorized and qualified personnel may do any of the assembly, disassembly, installation and
commissioning work. The relevant installation and operating regulations must be observed when
setting up or operating explosion-protected electrical systems.
- Always disconnect the device from voltage before assembly/disassembly.
- Follow the components mounting/operating instructions from this document.
When assembling the device, take care that the distances between the outside edge of the upper
flame-proof gap and the fixed obstacles that are not part of the device are for gas/vapour sub-
group IIB at least 30 mm (1.181 in).

«
...
5
6
7
8
9
...
»

Содержание Rexroth CIMS Mk IV





























































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth CIMS Mk IV

Бренд: GARO Страницы: 23

Бренд: Rally Pack Страницы: 2

Бренд: rako Страницы: 3

Бренд: Panasonic Страницы: 72

AS5000 - Transcription Kit - Digital Voice...

Бренд: Olympus Страницы: 17

A44 sound rocker

Бренд: LumiSource Страницы: 8

Бренд: Razorri Страницы: 26

WrapAround Windjammer

Бренд: Bestop Страницы: 7

Ceiling Trim Kit for Home2 Series

Бренд: Elite Screens Страницы: 8

Бренд: Black Box Страницы: 2

Brica Firefly Baby In-Sight

Бренд: Munchkin Страницы: 11

Бренд: DrBrowns Страницы: 2

Бренд: ESAB Страницы: 12

Бренд: Orno Страницы: 4

Monitor _QSG_DE01

Бренд: M-Audio Страницы: 6

Бренд: Speaka Professional Страницы: 68

Бренд: Metra Electronics Страницы: 20

Бренд: Yeti Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды