English |
19
Bosch Power Tools
1 609 92A 1C8 | (24.6.15)
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance.
Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
Release the On/Off switch and set it to the off position
when the power supply is interrupted, e. g., in case of a
power failure or when the mains plug is pulled.
Do not touch grinding and cutting discs before they
have cooled down.
The discs can become very hot while
working.
Secure the workpiece.
A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Products sold in GB only:
Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only:
Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions.
Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for cutting, roughing and brushing of
metal and stone materials without the use of water.
For cutting with bonded abrasives, a special cutting guard
(accessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
With approved sanding tools, the machine can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1
Release lever for protection guard
2
Spindle lock button
3
On/Off switch
4
Thumbwheel for speed preselection
(PWS 1000-125 CE/PWS 1300-125 CE)
5
Auxiliary handle (insulated gripping surface)
6
Grinder spindle
7
Protection guard for grinding
8
Mounting flange
9
Grinding wheel*
10
Clamping nut
11
Quick-clamping nut
*
12
Protection guard for cutting*
13
Cutting disc*
14
Hand guard*
15
Rubber sanding plate*
16
Sanding sheet*
17
Round nut*
18
Cup brush*
19
Cutting guide with dust extraction protection guard *
20
Diamond cutting disc*
21
Handle (insulated gripping surface)
22
Direction-of-rotation arrow on housing
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Angle Grinder
PWS ...
1000-125
1000-125 CE
1300-125 CE
Article number
3 603 ...
CA2 6..
CA2 8..
CA2 9..
Rated power input
W
1001
1010
1300
Rated speed
min
-1
11000
11500
11500
Speed control adjustment
min
-1
–
2800 – 11500
2800 – 11500
Grinding disc diameter, max.
mm
125
125
125
Thread of grinder spindle
M 14
M 14
M 14
Thread length (max.) of grinder spindle
mm
22
22
22
Reduced starting current
–
Constant electronic control
–
Speed preselection
–
Soft starting
–
Kickback stop
–
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
OBJ_BUCH-1961-006.book Page 19 Wednesday, June 24, 2015 9:26 AM
