Bosch Professional GWS 18V-15 C, Оригинальное руководство пользователя

Страница: 11 / 87

English | 11
Fitting
Using the GCY 42 Bluetooth ® Low Energy
Module
Note: The GCY 42 Bluetooth ® Low Energy Module is avail-
able as an accessory with GWS 18V-15 C power tools; it is
included in the scope of delivery for GWS 18V-15 SC power
tools.
Read the corresponding operating instructions for informa-
tion about the
Bluetooth ® Low Energy Module GCY 42 .
Charging the battery
u
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
Do not continue to press the On/Off switch after the
power tool has automatically switched off.
The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery
The battery (7) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release button
(8) is pressed unintentionally. As long as the battery is inser-
ted in the power tool, it is held in position by means of a
spring.
To remove the battery
(7) , press the release button (8) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
to
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Note: The state of charge of the battery is also displayed on
the user interface (4) (see "Status Indicators", page 14).
Battery model GBA 18V...
LEDs Capacity
3× continuous green light 60−100 %
2× continuous green light 30−60 %
1× continuous green light 5−30 %
1× flashing green light 0−5 %
Battery model ProCORE18V...
LEDs Capacity
5× continuous green light 80−100 %
4× continuous green light 60−80 %
3× continuous green light 40−60 %
2× continuous green light 20−40 %
1× continuous green light 5−20 %
1× flashing green light 0−5 %
Fitting Protective Equipment
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
Place the protective guard
(10) onto the holder on the
power tool until the coding
cams of the protective guard
are aligned with the holder.
When doing so, press and
hold the unlocking lever
(1) .
Press the protective guard
(10) onto the spindle collar
until the shoulder of the pro-
tective guard is sitting on the
flange of the power tool and
rotate the protective guard
until it audibly clicks into
place.
Adjust the position of the protective guard (10) to meet the
requirements of the operation. To do this, push the unlock-
ing lever
(1) upward and rotate the protective guard (10)
into the required position.
Bosch Power Tools 1 609 92A 5RK | (07.10.2020)