Bosch Nexxt Premium WFMC6400UC Скачать руководство пользователя страница 63

Страница: 63 / 75

1st Edition/Revision 6 (2/2/04)

WFMC Service Tips

Test Program (2C): Motor Control

Fault Codes (Test 1)

Test

P1:ERRORS

P:01

(Viewing motor control fault codes) --

Start & end test

pushing

Start/Pause

button. Scroll through list of (18) fault codes by pushing

Spin Selection

(WFMC3200) or

Menu

(WFMC6400) buttons.

•

WFMC3200 display alternates between fault code (e.g.

d:01

) & when fault occurred on in last 16

washes (e.g.

C:00

) – shows

C:00

if fault didn’t occur.

•

WFMC6400 display shows fault code & when fault occurred on in last 16 washes (e.g.

0 - dr:01

Last 16 fault codes are

stored & displayed!

HINT: # of faults reads “

”

for faults which didn’t occur.
Look at # of faults, not error
#, to see if faults occurred --
scroll thru all faults to check
if any occurred.

WFMC32

Display

WFMC64

Display

Test #

Problem

Possible Cause(s)

d:01

dr:01

P:04

Motor control short circuit

Faulty motor control.

d:02

dr:02

P:04

Motor control interruption

Faulty motor control.

d:03

dr:03

P:04

Damaged motor control temperature sensor Faulty temperature sensor.

d:06

dr:06

P:04

NTC relay failure

NTC too hot or relay stuck closed.

d:07

dr:07

P:04

Motor winding short circuited

d:08

dr:08

P:04

Motor speed sensor failed

Faulty speed sensor or wire harness.

d:09

dr:09

P:04

Voltage too high

Faulty motor control.

d:10

dr:10

P:04

Power limiter switch off

Motor overloaded or binding.

d:11

dr:11

P:04

Voltage too low

Faulty motor control.

d:12

dr:12

P:04

Motor control high current switch off

Motor overloaded or binding.

d:13

dr:13

P:04

Motor control high temperature switch off

Motor overloaded or binding.

d:14

dr:14

P:04

Motor control high temperature warning

Motor overloaded or binding.

d:15

dr:15

P:04

Power limiter warning

Motor overloaded or binding.

d:16

dr:16

P:04

Motor high temperature switch off

Motor overloaded or binding.

d:17

dr:17

P:04

Motor high temperature warning

Motor overloaded or binding.

d:18

dr:18

P:04

Peak voltage too high

Faulty motor control.

Содержание Nexxt Premium WFMC6400UC












































































Результаты поиска

Содержание Nexxt Premium WFMC6400UC

Отзывы:

Бренды по названию

Популярные бренды

Bosch Nexxt Premium WFMC6400UC, Руководство по обучению

Результаты поиска

Содержание Nexxt Premium WFMC6400UC

Отзывы:

Бренды по названию

Популярные бренды