Bosch Nexxt Premium WFMC6400UC Скачать руководство пользователя страница 62

Страница: 62 / 75

1st Edition/Revision 6 (2/2/04)

WFMC Service Tips

Test Program (2B): Module Fault

Codes (Test 1)

Test

P1:ERRORS

P:01

(Viewing control module fault codes) --

Start & end test

(WFMC6400) /

(P:01)

(WFMC3200) by pushing

Start/Pause

button. Scroll through list of fault codes

by pushing

Spin Selection

(WFMC3200) or

Menu

(WFMC6400) buttons.

•

WFMC3200 display alternates between fault code (e.g.

E:01

) & when fault occurred on in last 8

washes (e.g.

C:00

) – shows

C:00

if fault didn’t occur.

•

WFMC6400 display shows fault code & when fault occurred on in last 8 washes (e.g.

0 - Er:01

Last 8 fault codes are

stored & displayed!

HINT: # of faults reads “

”

for faults which didn’t occur.
Look at # of faults, not error
#, to see if faults occurred -
- scroll thru all faults to
check if any occurred.

WFMC32

Display

WFMC64

Display

Test #

Problem

Possible Cause(s)

E:01

Er:01

washing

Door open

Door lock not engaged

E:02

Er:02

washing

Door lock doesn't unlock

Jammed lock or bad wire harness

E:03

Er:03

washing

Door lock doesn't lock

Jammed lock or bad wire harness

E:04

Er:04

washing

Door control broken

Faulty Triac or control module

E:05

Er:05

P:16

NTC open-circuited

Faulty NTC or bad wire harness

E:06

Er:06

P:16

NTC shorted

Faulty NTC or bad wire harness

E:07

Er:07

P:16

Unexpected heating (heater on at wrong time) Faulty heater or stuck heater relay

E:08

Er:08

P:16

Heater doesn't shut off

Faulty heater or stuck heater relay

E:09

Er:09

P:4

Communication lost to motor

Faulty wire harness

-----

Er:10

P:11

Flow meter gives wrong values

Faulty flow meter or wire harness

-----

Er:11

P:8/9/13

No water flow (within 6 minutes)

Faulty inlet valve, wire harness, hose

E:12

Er:12

P:8/9/13

Water supply time exceeded

Faulty inlet valve, wire harness, hose

E:13

Er:13

P:15

Drain pump time exceeded

Faulty drain pump, wire harness, hose

E:14

Er:14

P:9

Overflow level exceeded

Faulty/blocked pump, hose, inlet valve

-----

Er:15

P:8

Pressure sensor gives failure voltage level

Faulty pressure sensor, wire harness

-----

Er:16

P:8

Can't calibrate pressure sensor

Faulty pressure sensor, wire harness

E:20

Er:20

P:4

Spinning aborted due to unbalanced load

Unbalanced load or faulty wire harness

E:21

Er:21

Excessive foam

Wrong or too much detergent used

E:22

Er:22

washing

Frequency synchronization failed

Faulty control module

E:24

Er:24

P:4

Motor power relay failed

Faulty control module

Содержание Nexxt Premium WFMC6400UC












































































Результаты поиска

Содержание Nexxt Premium WFMC6400UC

Отзывы:

Бренды по названию

Популярные бренды

Bosch Nexxt Premium WFMC6400UC, Руководство по обучению

Результаты поиска

Содержание Nexxt Premium WFMC6400UC

Отзывы:

Бренды по названию

Популярные бренды