Bosch NBC-265-P Скачать руководство пользователя страница 53

Страница: 53 / 106

IP Camera 200 Series

Advanced Mode | en

Bosch Security Systems

Installation and Operation Manual

AR18-10-B012 | v1.5 | 2011.01

Note:

If a device had primary and secondary recording running on the

SD card and is then added to a VRM system, the blocks used for

primary recording will not be re-used, reducing the available

recording space for ANR recording. This can be solved by re-

formatting the SD card.

Throughput limit for simultaneous recording and local replay at

100% playback speed is:

–

maximum total recording bit rate of 7 Mbps for external

iSCSI recording.

–

maximum total recording bit rate of 10 Mbps for SD card

recording, depending on SD card performance.

Activating and Configuring Storage Media

The storage overview displays the available storage media.

Select individual media or iSCSI drives and transfer these to the

Managed storage media

list. Activate the storage media in this

list and configure them for storage.

Note:

Each storage medium can only be associated with one user. If a

storage medium is already being used by another user,

decouple the user and connect the drive to the camera. Before

decoupling, make absolutely sure that the previous user no

longer needs the storage medium.

In the

Recording media

section, click the

iSCSI Media

Local Media

tab to display the applicable storage media in

the overview.

In the

Storage overview

section, double-click the required

storage medium, a SD card, an iSCSI LUN or one of the

other available drives. The medium is then added to the

Managed storage media

list. Newly added media is

indicated in the

Status

column by the status

Not active

Click

Set

to activate all media in the

Managed storage

media

list. These are indicated in the

Status

column by the

status

Online

Содержание NBC-265-P











































































































Результаты поиска

Содержание NBC-265-P

Отзывы:

Похожие инструкции для NBC-265-P

Бренды по названию

Популярные бренды

Bosch NBC-265-P, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NBC-265-P

Отзывы:

Похожие инструкции для NBC-265-P

Бренды по названию

Популярные бренды