Bosch NBC-265-P Скачать руководство пользователя страница 35

Страница: 35 / 106

IP Camera 200 Series

Advanced Mode | en

Bosch Security Systems

Installation and Operation Manual

AR18-10-B012 | v1.5 | 2011.01

–

live

is the lowest authorization level. It can only be used to

view the live video image and switch between the different

live image displays.

Use the various authorization levels to limit access. Proper

password protection is only guaranteed if all higher

authorization levels are also protected with a password. For

example, if a

live

password is assigned, a

service

and a

user

password should also be set. When assigning passwords,

always start from the highest authorization level,

service

, and

use different passwords.

Password

Define and change a separate password for each level while

logged in as

service

or if the device is not protected by a

password. Enter the password (19 characters maximum) for

the selected level.

Confirm password

Re-enter the new password to ensure that there are no typing

mistakes.

The new password is only saved after clicking

Set

. Therefore,

click

Set

immediately after entering and confirming the

password, even if assigning a password at another level.

Содержание NBC-265-P











































































































Результаты поиска

Содержание NBC-265-P

Отзывы:

Похожие инструкции для NBC-265-P

Бренды по названию

Популярные бренды

Bosch NBC-265-P, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NBC-265-P

Отзывы:

Похожие инструкции для NBC-265-P

Бренды по названию

Популярные бренды