Bosch Mastertech M-VCI Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 20

Bosch Mastertech M-VCI Скачать руководство пользователя страница 8

Robert Bosch LLC

M-VCI – NETGEAR® Router Installation Guide Index | Version 1.0 | April 2011

5

| Installation Steps |

Step 1

This shows the NETGEAR pre-
configured router installed into a
network (Setup Type II) without
any pre-existing wireless router.
No network changes are necessary
for DSL/cable modem or wired
computers.

This shows the NETGEAR pre-
configured router installed as a
stand-alone device (Setup Type III)
without internet.

Installation Steps

Step 1 - NETGEAR Router

configuration (For: Types I,

II & III) (Getting Started)

f

Connect the NETGEAR router
to AC power

f

Disable the wireless card on
your computer

f

Disconnect all wired network
connections

f

Connect the router to the
computer LAN port

f

Reboot the computer
(to renew the IP address)

f

Open your web browser

f

Enter http://192.168.1.1 into
your browser address bar and
press <Enter>

f

Enter User Name and Password

– User Name:

admin

– Password:

password

Note:

The router does not need

internet connection at this time.

«
...
6
7
8
9
10
...
»

Содержание Mastertech M-VCI





















Отзывы:

Нет отзывов