Bosch Mastertech M-VCI Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 20

Bosch Mastertech M-VCI Скачать руководство пользователя страница 11

M-VCI – NETGEAR® Router Installation Guide Index | Version 1.0 | April 2011

Robert Bosch LLC

Installation Steps |

Step 2 | 8

Step 2 - Connecting Your

Wired Devices “Special

Instruction for Type II”

Important:

Use the same PC that

was originally connected to the
modem for these steps.

f

Connect the computer to the
LAN port of the NETGEAR
Router

f

Reboot the computer (to
renew the NETGEAR Smart
Wizard IP Address)

f

Open your Web Browser

f

Enter http://192.168.10.1 into
your browser address bar and
Press: <Enter>

f

Enter User ID and Password

– User ID:

admin

– Password:

Bosch_VCI_AP

– Click: OK

Caution!

Do not connect the

router to the cable/DSLmodem at
this time.

Step 2 - Connecting Your

Wired Devices “Special

Instruction for Type II”

(Setting NETGEAR Router

configuration)

f

Click: Basic Settings

Step 2 - Connecting Your

Wired Devices “Special

Instruction for Type II”

(Setting NETGEAR router

MAC Address)

f

Click: Use Computer MAC
address

f

Click: Apply

f

Wait for the router to apply
settings

«
...
9
10
11
12
13
...
»

Содержание Mastertech M-VCI





















Отзывы:

Нет отзывов