Bosch KALKHOFF PERFORMANCE, Оригинальное руководство пользователя

Страница: 53 / 103

Assembly
Inserting and removing the battery pack
For inserting and removing the eBike battery pack in/from the
eBike, please read and observe the battery pack operating in-
structions.
Checking the Speed Sensor (see figure A)
The speed sensor
2
and its spoke magnet
3
must be mounted
in such a manner that the spoke magnet, after a turn of the
wheel, moves past the speed sensor with a clearance of at
least 5 mm, yet no more than 17 mm.
Note:
If the distance between speed sensor
2
and spoke mag-
net
3
is too small or too large, or if the speed sensor
2
is not
properly connected, the speed indication will fail, and the
eBike drive unit will operate in emergency mode.
In this case, loosen the screw of the spoke magnet
3
and fas-
ten the spoke magnet to the spoke in such a manner that it
runs past the mark of the speed sensor at the correct clear-
ance. If the speed is still not being indicated in the speed indi-
cation after this, please contact an authorised bicycle dealer.
Operation
Initial Operation
Requirements
The eBike system can only be activated when the following re-
quirements are met:
– A sufficiently charged battery pack is inserted (see battery
pack operating instructions).
– The on-board computer is properly inserted in the holder
(see on-board computer operating instructions).
– The speed sensor is connected properly (see “Checking
the Speed Sensor”, page
3
).
Switching the eBike System On/Off
Options for
switching on
the eBike system:
– If the on-board computer is already switched on when you
insert it into the holder, then the eBike system will be
switched on automatically.
– When the on-board computer and the eBike battery pack
are inserted, briefly press the On/Off button of the on-
board computer.
– When the on-board computer is inserted, press the On/Off
button of the eBike battery pack (see battery pack operat-
ing instructions).
Once switched on, the eBike system is in the
“OFF”
mode. Se-
lect the desired assistance level and set off.
Note:
Depending on the version, you can also start in the pre-
viously set mode.
The drive is activated as soon as you step on the pedals (ex-
cept when in the push aid feature, see “Switching the Push-
assistance mode On/Off”, page
53
). The motor out-
put depends on the settings of the assistance level on the on-
board computer.
As soon as you stop pedaling when in normal operation, or as
soon as you have reached a speed of 45 km/h, the assistance
from the eBike drive is switched off. The drive is automatically
re-activated as soon you start pedaling again and the speed is
below 45 km/h.
Options for
switching off
the eBike system:
– Press the On/Off button of the on-board computer.
– Switch the eBike battery pack off by its On/Off button (see
battery pack operating instructions).
– Remove the on-board computer out of its holder.
If the eBike is not moved
and
no button is pressed on the on-
board computer for 10 minutes, the eBike system will shut
down automatically in order to save energy.
eShift (optional)
eShift is the integration of automatic gear shifting systems in-
to the eBike system. The eShift components are electrically
connected to the drive unit by the manufacturer. The opera-
tion of automatic gear shifting systems is described in the op-
erating instructions of the on-board computer.
Setting the Assistance Level
On the on-board computer you can set how much the eBike
drive assists you while pedalling. The assistance level can be
changed at any time, even while cycling.
Note:
For individual versions, it is possible that the assistance
level is pre-set and cannot be changed. It is also possible that
less assistance levels are available for selection than listed
here.
Bike lights
1)
Voltage, approx.
2)3)
V 6/12
Maximum output
– Front light
– Taillight
W
W 8.4/17.4
0.6/0.6
1) Not possible via the eBike battery pack in all country-specific
versions, depending on the statutory regulations
2) The voltage level is preset and can be changed only by the bicycle
dealer.
3) When changing the bulbs, ensure that the bulbs are compatible with
the Bosch eBike system (ask your bicycle dealer) and that the specified
voltage matches. Bulbs must be replaced only with bulbs of the same
voltage.

Incorrectly inserted bulbs can be destroyed!
OBJ_BUCH-2822-001.book Page 2 Wednesday, April 13, 2016 4:09 PM
52