Bosch HBC53R550, Инструкция по эксплуатации

Страница: 12 / 24

12
Cleaning system
The cleaning system regenerates the self-cleaning surfaces in
the cooking compartment.
The back wall, ceiling and side walls of the cooking
compartment are coated with a highly porous ceramic layer.
This coating absorbs and disintegrates splashes from baking
and roasting while the oven is in operation. If these self-
cleaning surfaces no longer clean themselves adequately, they
can be regenerated with the cleaning system.
Before cleaning
Remove accessories and cookware from the cooking
compartment.
Cleaning the cooking compartment floor
Before you set the cleaning system, clean the surfaces in the
cooking compartment that are not self-cleaning. Otherwise,
stains will develop that it is not possible to remove.
Use a dish cloth and hot soapy water or a vinegar solution. If
there are heavy deposits of dirt, use a stainless steel scouring
pad or oven cleaner. Only use when the cooking compartment
is cold. Never treat the self-cleaning surfaces with a scouring
pad or oven cleaner.
Making settings
Cleaning takes approximately one hour.
1.
Set the function selector to < 3D hot air.
2.
Set the temperature selector to
s
.
3.
Press the u button.
The
u
symbol lights up in the display. The time at which the
cleaning will end appears and the p symbol is in brackets.
Cleaning will start after a few seconds. You will see the time
counting down and the
r
symbol will be in brackets. The
p
symbol goes out.
Cleaning is finished
A signal sounds. The oven stops heating. 00:00 is shown in the
display. Press the
0
button twice and turn the function selector
to the off position. The oven switches off.
Cancelling cleaning
Press the
u
button and turn the function selector to the off
position. The oven switches off.
Setting a later end time
You can delay the time at which the cleaning programme is due
to finish. For instance, you can set the cleaning programme to
run at night so that you can use your oven during the day.
Make the settings as described in steps 1 to 3. Before cleaning
starts, use the
@
or
A
button to set a later end time.
The oven switches to standby. The display shows the time at
which the cleaning will finish and the
p
symbol is in brackets.
When cleaning starts, you can see the time counting down in
the display and the
r
symbol is in brackets. The
p
symbol
goes out.
After cleaning
When the cooking compartment has cooled down completely,
wipe the salt residues off the self-cleaning surfaces with a
damp cloth.
Troubleshooting
Malfunctions often have simple explanations. Refer to the table
before calling the after-sales service as you may be able to
remedy the fault yourself.
Malfunction table
If a dish doesn't turn out as well as you had hoped, refer to the
section Tested for you in our cooking studio , where you will
find plenty of cooking tips and tricks.
Error messages
If an error message with “ appears, press the 0 button. The
message disappears. A time function that has been set is
cleared. If the error message does not disappear, please
contact the after-sales service.
You can take remedial action yourself if the following error
message is displayed.
ã=
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out by one of our trained after-sales engineers.
Replacing the oven light bulb
Replace faulty oven light bulbs.
You can obtain replacement light bulbs from customer service
or specialist retailers: E14, 220 - 240 V, 40 W, heat resistant to
300 °C. Only use these oven light bulbs.
ã=
Risk of electric shock !
Disconnect the appliance from the power supply. Switch off the
circuit breaker or remove the fuse from the household fuse box.
Problem Possible cause Remedy/information
The oven does
not work.
The circuit
breaker is
defective.
Look in the fuse box and
check that the circuit
breaker is in working order.
Power cut Check whether the kitchen
light or other kitchen appli-
ances are working.
0
and zeros
light up in the
display.
Power cut Reset the clock.
The oven does
not heat up.
There is dust on
the contacts.
Turn the control knobs back
and forth several times.
Error message Possible cause Remedy/information
“‹‚‚
A button was
depressed for
too long or is
covered up.
Press all buttons individu-
ally. Check whether any but-
tons are jammed, covered
up or soiled.