Bosch GST 65 E Professional, Руководство по эксплуатации

Страница: 13 / 18

Jigsaw
Part number
Power input
Output
Frequency
Stroke rate at no load
Stroke
Cutting wood up to
Performance aluminium up to
in non-alloyed steel up to
Bevel cuts (left/right)
Weight approx.
Safety class.
GST 65 E
0 601 281 7..
450 W
270 W
50 / 60 Hz
500 - 3100 min
-1
22 mm
65 mm
15 mm
4 mm
0-45°
1,7 Kg
/II
GST 65
0 601 281 0..
450 W
270 W
50 / 60 Hz
3100 min
-1
22 mm
65 mm
15 mm
4 mm
0-45°
1,7 Kg
/II
PRODUCT SPECIFICATION
On/Off switch
Stroke rate selection thumbwheel (GST 65 E)
Locking button for on/off switch
Dust cover for vacuuming
Contact protector
Saw blade*
Guide roller
SDS lever for saw blade release
Base plate
Ventilation slots
Vacuum hose**
Splintering protector
Blade device
Thread
Screw
Triangle**
Circle Cutter/Parallel Guide**
The machine is intended for making separating cuts and
cutouts in wood, plastic, metal, ceramic plates and rubber
while resting resting firmly on the work piece.
It is suitable for straight and curved cuts with mitre angles to 45°.
The saw blade recommendations are to be observed.
Working safely with this machine is possible
only when the operating and safety information
are read completely and the instructions
contained therein are strictly followed. In
MACHINE ELEMENTS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
*Optional accessories
**Commercially available (not included in the delivered items)
Not all of the accessories illustrated or described are
included as standard delivery
GB
INTENDED USE
FOR YOUR SAFETY
Measured values determined according to IEC 60745.
Typically the A-weighted sound pressure level of the tool is
82 dB (A).
Wear ear protection!
The typical weighted acceleration is 5m/s 2 .
NOISE/VIBRATION INFORMATION
addition, the general safety instructions in the enclosed
booklet must be followed. Before using for the first time,
ask for a practical demonstration.
If the cable is damaged or cut through while
working, do not touch the cable but immediately
pull the mains plug. Never use the machine with a
damaged cable.
For the mounting and replacing of the saw blade 6,
wear protective gloves.
Wear protective goggles when working with materials
which produce large amounts of chips. For work
which produces dust that is detrimental to health, a
dust protection mask should be worn.Materials
containing asbestos should not be worked.
When working, never place a hand or fingers in
front of the saw blade.
The improper use of accessories which are not
intended for this machine type increases the danger
of an accident and can lead to damage to the
machine.
• Connect machines that are used in the open via a fault
current (FI) circuit breaker with a triggering current of 30 mA
maximum. Use only extension cable that are intended for
outdoor use and are protected against splash water.
• When working with the machine, always hold it firmly with
both hands and provide for a secure stance.
• Always direct the cable to the rear away from the machine.
• Apply the machine to the work piece only when switched on.
• The cutting path must be free of obstacles both above and blow.
• When sawing, the complete surface of the base plate 9
should securely rest on the material. For the working of smaller
or thin workpieces, use a stable foundation or a saw table
(accessory)
• When the cut is completed, switch off the machine and then
pull the saw blade out of the cut only after it has come to a
standstill (danger of Kick-Back)
• Do not brake the saw blade to a stop by applying side
pressure after switching off.
• Use only sharp, flawless saw blades. Replace immediately
cracked, bent dull saw blades.
• Bosch can assure flawless functioning of the machine
only when original accessories are used.
13