8
| English
1 609 92A 1W8 | (22.6.16)
Bosch Power Tools
21
Vacuum hose*
22
Splinter guard
23
Nose plastic sliding shoe
24
Screw
25
Scale for mitre angle
26
Locking screw for parallel guide*
27
Parallel guide with circle cutter*
28
Centring tip of the circle cutter*
29
Allen key
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Assembly
Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Battery Charging
Use only the battery chargers listed on the accessories
page.
Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note:
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
5
show the charging status of the battery
1
. The battery
charge-control indicator only illuminates for 5 seconds after
start-up.
When no LED lights up after switching on, then the battery is
defective and must be replaced.
Replacing/Inserting the Saw Blade
When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of these instructions. Use only T-shank saw blades. The saw
blade should not be longer than required for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A)
Clean the shank of the saw blade before inserting it.
An unclean shank cannot be fastened securely.
Insert the saw blade
14
into the stroke rod
11
until it latches.
The SDS lever
18
automatically snaps to the rear and the saw
blade is locked. Do not manually press the lever
18
toward
the rear, otherwise you could damage the machine.
While inserting the saw blade, pay attention that the back of the
saw blade is positioned in the groove of the guide roller
10
.
Check the tight seating of the saw blade.
A loose saw
blade can fall out and lead to injuries.
Ejecting the Saw Blade (see figure B)
When ejecting the saw blade, hold the machine in such
a manner that no persons or animals can be injured by
the ejected saw blade.
Turn the SDS lever
18
forward towards the contact protector
19
to the stop. The saw blade is released and ejected.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Cordless Jigsaw
GST 10,8 V-LI
Article number
3 601 EA1 0..
Rated voltage
V=
10.8
Stroke rate at no load n
0
min
-1
1500 –2800
Stroke
mm
18
Cutting capacity, max.
– in wood
– in aluminium
– in non-alloy steel
mm
mm
mm
70
3
3
Bevel cuts (left/right), max.
°
45
Weight according to EPTA-
Procedure 01:2014
kg
1.5 - 1.7*
* dependent of the battery pack being used
LED
Capacity
Continuous lighting 3 x green
≥
2/3
Continuous lighting 2 x green
≥
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
Flashing light 3 x green
Empty
OBJ_BUCH-2066-003.book Page 8 Wednesday, June 22, 2016 8:21 AM
