Bosch Greentherm 9800 SECO 199 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 52

background image

6 720 817 281 (2017/05)

Greentherm 9800 SEO 160/199 | SECO 199

26 | Electrical connections

The water heater requires an electrical power supply from a
120VAC / 60Hz properly rated receptacle and must be
properly grounded.
The water heater is wired as shown in the wiring diagram
(chapter 12, Fig. 34).

Fig. 20

Connecting power supply cord

[1] Waterproof outlet
[2] Power cord length: 5.9ft (1.8m).

Note: The power supply that the appliance is plugged into
should be protected from possible water damage. Observe
proper clearance to avoid damages.

7.2

Position of the fuses in control unit

To check the fuse, proceed as follows:

▶ Disconnect the unit from the power supply before

removing the front cover.

▶ Remove the front cover, see fig. 3, page 9.
▶ Remove the two phillips head screws securing the control

unit.

▶ Disconnect all the cables from the control unit.

▶ Press the four snaps of the control unit and remove the

cover.

Fig. 21

Control Unit

▶ Press the four snaps inside the control unit and remove the

PCB.

▶ Check the fuse on the printed circuit board, for electrical

continuity, see fig. 22, [1].

Fig. 22

Fuse position

[1] Fuse

▶ After checking the fuse, reinstall all parts in reverse order.

DANGER:

Electric shock!

▶ Field wiring connections and electrical

grounding must comply with local
codes, or in the absence of local codes,
with the latest edition of the National
Electric Code, ANSI/NFPA 70, or in
Canada, all electrical wiring must
comply with the local codes and the
Canadian Electrical Code, CSA C22.1
Part 1.

DANGER:

Electric shock!

Shock hazard: line voltage is present.

▶ Before servicing the water heater,

unplug power supply cord from outlet.
Failure to do so could result in severe
personal injury or death.

«
...
24
25
26
27
28
...
»

Содержание Greentherm 9800 SECO 199





















































Отзывы:

Нет отзывов

Похожие инструкции для Greentherm 9800 SECO 199

Бренд: L.B. White Страницы: 28

Бренд: umbra pompe Страницы: 16

Бренд: A.O. Smith Страницы: 2

Бренд: Gamo Страницы: 25

Бренд: Gamma Vacuum Страницы: 27

Бренд: KDK Страницы: 40

PELLEMATIC SmartXS

Бренд: MAINE ENERGY SYSTEMS Страницы: 82

Бренд: Radiant Страницы: 8

Бренд: Radialight Страницы: 80

Бренд: Radialight Страницы: 80

Бренд: Calpeda Страницы: 32

Бренд: RainSoft Страницы: 16

Бренд: Zehnder Rittling Страницы: 20

Бренд: Dancover Страницы: 7

Бренд: Ballu-Biemmedue Страницы: 29

Бренд: Neilsen Страницы: 8

Бренд: MILL Страницы: 144

Бренд: GE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды