Bosch GLM 150 C, Оригинальное руководство пользователя

Страница: 15 / 80

English | 15
Move the measuring tool until the required distance value is
shown in the display below.
09.06.2017
13:20:23
0.0º
max
min
m
m 1.291
m 11.623
11.623
Briefly pressing the measuring button (2) [ ]
will interrupt the continuous measurement.
The current measured value will be shown at
the bottom of the display. The maximum and
minimum measured value appear above it.
Pressing the measuring button
(2) [ ] once
more will start the continuous measurement again.
Continuous measurement automatically switches off after
five minutes.
Area measurement
Select the area measurement mode .
Then measure the width and length and height one after the
other as with a length measurement. The laser beam remains
switched on between the two measurements. The distance
to be measured flashes in the indicator for area measure-
ment
(see indicator element (j) ).
09.06.2017
13:20:23
0.0º
43.050 m 2
m 4.640
m 9.279
The first measured value is shown at the top of
the display.
After the second measurement has been com-
pleted, the area will be automatically calcu-
lated and displayed. The end result is shown at
the bottom of the display, while the individual
measured values are shown above it.
Volume measurement
Select the volume measurement mode .
Then measure the width, length and depth one after the
other as with a length measurement. The laser beam remains
switched on between the three measurements. The distance
to be measured flashes in the indicator for volume measure-
ment
(see display element (j) ).
09.06.2017
13:20:23
0.0º
m 4.640
m 9.279
m 13.919
599.276 m 3
The first measured value is shown at the top of
the display.
After the third measurement has been com-
pleted, the volume will be automatically calcu-
lated and displayed. The end result is shown at
the bottom of the display, while the individual
measured values are shown above it.
Indirect distance measurement
Select the indirect distance measurement mode . There
are four measuring functions available for the indirect dis-
tance measurement, each of which is capable of determining
different distances.
The indirect distance measurement is used to determine dis-
tances that cannot be measured directly, due to an obstacle
that would impede the path beam or the absence of a target
surface that could serve as a reflector. This measuring pro-
cedure can only be employed vertically. Any horizontal devi-
ation will lead to measurement errors.
Note: Indirect distance measurement is always less accurate
than direct distance measurement. For application-related
reasons, measuring errors can be greater than with direct
distance measurement. To improve the accuracy of meas-
urement, we recommend the use of a tripod (accessory).
The laser beam remains switched on between the individual
measurements
a) Indirect height measurement (see figure B)
Select the indirect height measurement mode .
Ensure that the measuring tool is at the same height as the
lower measuring point. Then tilt the measuring tool around
the reference level and measure distance
1 as for a length
measurement (displayed as a red line).
09.06.2017
13:20:23
45º
m 37.116
45.0
26.245 m
Once the measurement is complete, the result
for the required distance
X is displayed in the
result line (a) . The measured values for dis-
tance 1 and angle α can be found in the meas-
ured value rows (h) .
b) Double indirect height measurement (see figure C)
The measuring tool can indirectly measure all distances that
lie in the vertical level of the measuring tool. Select the
double indirect height measurement mode . Measure dis-
tances
1 and 2 in succession as for a length measurement.
09.06.2017
13:20:23
º
30º
32.852 m
m 48.873
m 56.335
35.5
Once the measurement is complete, the result
for the required distance
X is displayed in the
result row (a) . The measured values for dis-
tances 1 and 2 and angle α can be found in the
measured value rows (h) .
Ensure that the reference level for the meas-
urement (e.g. the rear edge of the measuring tool) remains
in exactly the same place for all the individual measurements
in a single measuring process.
a) Indirect length measurement (see figure D)
Select the indirect length measurement mode .
Ensure that the measuring tool is at the same height as the
required measuring point. Then tilt the measuring tool
around the reference level and measure distance
1 as for a
length measurement.
09.06.2017
13:20:23
60º
m 153.104
60.0
76.552 m
Once the measurement is complete, the result
for the required distance
X is displayed in the
result row (a) . The measured values for dis-
tance 1 and angle α can be found in the meas-
ured value row (h) .
d) Trapezium measurement (see figure E)
The trapezium measurement can be used to determine the
length of a roof slope, for example.
Select the trapezium measurement .
Measure distances
1 , 2 and 3 in succession as for a length
measurement. Ensure that the measurement of distance 3
begins exactly at the point where distance 1 ends and that
distances 2 and 3 are at right angles to distance 1 .
09.06.2017
13:20:23
60º
m 3.624
m
2.456
m 4.872
4.356 m
Once the final measurement is complete, the
result for the required distance
X is displayed
in the result line (a) . The individual measured
values can be found in the measured value
lines
(h) .
Bosch Power Tools 1 609 92A 4XP | (11.01.2019)