8
| English
1 609 92A 2HK | (10.3.16)
Bosch Power Tools
Technical Data
Assembly
Before any work on the machine itself, pull the mains
plug.
Dust Extraction
Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace.
Dust can
easily ignite.
Mounting/Replacing the Diamond Cutting Disc
(see figure A)
When mounting and replacing diamond cutting discs, it
is recommended to wear protective gloves.
Diamond cutting discs become very hot during opera-
tion; do not touch them until they have cooled down.
Always use a correctly sized diamond cutting disc with
the fitting mounting hole that corresponds with the in-
formation listed in the technical data.
Use only diamond-tipped cutting discs. Segmented dia-
mond wheels may only have negative cutting angles
and slots between the segments to a maximum of
10 mm.
Mounting the Diamond Cutting Disc
– Clean the diamond cutting disc
15
and all clamping parts
to be mounted.
– Mount the mounting flange
14
onto the drive spindle
13
.
– Place the diamond cutting disc
15
onto the mounting
flange
14
. The direction arrow on the diamond cutting disc
15
and the direction-of-rotation arrow on the blade guard
6
must correspond.
– Mount the clamping flange
16
and screw in the clamping
bolt
18
.
– Hold the clamping flange
16
with the ring spanner
17
and
tighten the clamping bolt
18
with the hex key
19
.
Removal of the Diamond Cutting Disc
– Hold the clamping flange
16
with the ring spanner
17
and
loosen the clamping bolt
18
with the hex key
19
.
– Remove the clamping flange
16
and diamond cutting disc
15
from the drive spindle
13
.
Operation
Operating Modes
Before any work on the machine itself, pull the mains
plug.
Adjusting the Cutting Angle (see figure B)
– Loosen wing bolt
9
. Tilt the machine sidewards until the
desired cutting angle is set on the scale
11
. Tighten wing
bolt
9
again.
Note:
For bevel cuts, the cutting depth is smaller than the set-
ting indicated on the cutting-depth scale
3
.
Pre-selecting the Cutting Depth (see figure C)
The cutting depth may only be pre-selected when the
machine is switched off.
Adapt the cutting depth to the thickness of the workpiece. For
optimum results, the diamond cutting disc must protrude ap-
prox. 2 mm out of the material.
– Loosen wing bolt
4
. For a smaller cutting depth, pull the
machine from the base plate
10
; for a larger cutting depth,
push the machine toward the base plate
10
. Adjust the de-
sired cutting depth at the cutting-depth scale
3
. Tighten
wing bolt
4
again.
Masonry Saw
GDM 13-34
GDM 13-34
Article number
3 601 36A 2..
3 601 36A 2B0
Rated power input
W
1300
1300
Rated speed
min
-1
12000
12000
Max. diameter for diamond cutting discs
mm
114
114
Cutting discs width, min.
mm
1.6
1.6
Cutting discs width, max.
mm
2.4
2.4
Mounting bore
mm
20
15
Cutting depth, max.
– for 0° bevel angle
– for 45° bevel angle
mm
mm
34
22
34
22
Weight according to EPTA-Procedure 01:2014
kg
2.8
2.8
Protection class
/
II
/
II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
OBJ_BUCH-936-006.book Page 8 Thursday, March 10, 2016 3:12 PM
