English |
21
Bosch Power Tools
1 609 92A 0XF | (30.9.14)
Noise Information
Sound emission values determined according to
EN 60335-2-69.
Typically the A-weighted sound pressure level of the vacuum
cleaner is lower than 70 dB(A). Uncertainty K= 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60335-1, EN 60335-2-69.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 30.09.2014
Assembly
Before any work on the vacuum cleaner itself, pull the
mains plug.
Mounting the Vacuum-hose Holder (see figure A)
– Slide the vacuum-hose holders
4
firmly from above into the
retainers
36
intended for this purpose, until they engage.
Mounting the Vacuum Hose (see figure B)
– Mount the vacuum hose
27
onto the hose connection
piece
3
and turn it in clockwise direction to the stop.
Note:
While vacuuming, an electrostatic charge develops in
the vacuum hose and accessories caused by the friction of the
dust, which the operator could experience in the form of stat-
ic discharging (dependent on environmental influences and
physical perception).
As a general rule, Bosch recommends using an anti-static vac-
uum hose (accessory) when vacuuming fine dusts and dry
materials.
Mounting VAC Accessories (see figure C)
The vacuum hose
27
is equipped with a clip system, with
which the VAC accessories (tool sleeve
25
, elbow
28
) can be
connected.
Mounting the Tool Sleeve
– Mount the tool sleeve
25
onto the vacuum hose
27
until
both snap-fasteners
37
of the vacuum hose can be heard
to engage.
– To disassemble, press both snap-fasteners
37
inward and
pull the components apart.
Mounting Nozzles and Tubes
– Mount the elbow
28
onto the vacuum hose
27
until both
snap-fasteners
37
of the vacuum hose can be heard to en-
gage.
– Afterwards, mount the desired VAC accessory (floor noz-
zle, crevice nozzle, vacuum tube, etc.) firmly onto the el-
bow
28
.
– To disassemble, press both snap-fasteners
37
inward and
pull the components apart.
Inserting/Removing a Disposal Bag or Dust
Bag (Dry Vacuuming) (see figure D)
For dry vacuuming of materials according to dust category M,
a disposal bag
29
or a dust bag
must
be inserted.
When vacuuming materials with or without an exposition limit
value ≥ 1 mg/m
3
(according to dust category L), it is possible
to vacuum directly into the container.
Note:
When using a paper filter bag, the automatic filter
cleaning (AFC) (see “Deactivating the AFC”, page 23)
must
,
and when using a fleece filter bag,
should
be shut off.
Do not fill the disposal bag
29
with more than
25 kg (max.)
.
The vacuum cleaner contains materials
that are hazardous to one’s health.
Have the emptying and maintenance, incl. the disposal of
dust-collection containers, carried out only by specialists.
Appropriate protective equipment is required. Do not op-
erate the vacuum cleaner without the complete filter sys-
tem.
Otherwise there is danger to your own health.
Inserting a Disposal Bag
– Unlock the latches
15
and remove the vacuum lid
13
.
– Insert the disposal bag
29
into the container
1
with the fill-
ing opening toward the front.
– Pull the filling opening over the connection flange into the
recess of the connection flange.
– Make sure that the disposal bag
29
faces completely
against the interior sides of the container
1
.
– Fold the rest of the disposal bag
29
over the edge of the
container
1
.
– Reattach the vacuum lid
13
again and lock the latches
15
.
Removing and Closing the Disposal Bag
– Unlock the latches
15
and remove the vacuum lid
13
.
– Pull the full disposal bag
29
toward the rear off of the con-
nection flange.
– Carefully remove the disposal bag
29
out of the vacuum
cleaner without damaging it.
When doing this, pay attention that the disposal bag does
not get caught or ripped open against the connection
flange or other sharp objects.
– Pull the cover off of the adhesive strip, close the disposal
bag and tape it shut.
Afterwards, tie off the disposal bag
29
below the filling
opening with the pulled off cover of the adhesive strip.
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
WARNING
OBJ_BUCH-1747-003.book Page 21 Tuesday, September 30, 2014 10:13 AM
