en
Cleaning and maintenance
10
Lighting
The lighting can be switched on and off independently
of the fan.
Touch the
B
symbol.
Setting the brightness
Press and hold the
B
symbol until the required
brightness is reached.
Saturation display
If the metal grease filters or the activated charcoal filter
are/is saturated, the corresponding symbols flashes
after the appliance is switched off:
■
Metal grease filters:
E
■
Activated charcoal filter:
F
■
Metal grease filters and activated charcoal filter:
E
and
F
If you have not yet done so, the metal grease filters
should now be cleaned or the activated charcoal filter
replaced.
~
"Cleaning and maintenance" on page 10
Note:
The saturation indicator does not apply for non-
renewable activated charcoal filters that are inserted
downstream of the metal grease filter. These activated
charcoal filters must be replaced twice a year.
The saturation indicators can be reset while they are
flashing. To do this, touch the appropriate symbol.
Switching over the display for air recirculation mode
For air recirculation mode, the electronic controller must
be switched over accordingly:
■
The extractor hood must be connected and switched
off.
■
Touch and hold the
D
symbol. Touch the "2"
symbol.Take your finger off the
D
symbol. This
will switch the electronic controller over to air
recirculation mode (filters that cannot be
regenerated).
■
Touch and hold the
D
symbol. Touch the "3"
symbol.Take your finger off the
D
symbol. This
will switch the electronic controller over to air
recirculation mode (filters that can be regenerated).
■
Repeatedly touching and holding the
D
symbol
and touching the "1" symbol switches the electronic
controller back over to air extraction mode.
Audible signal
Switching on
Touch and hold the
#
and
y
symbols at the same
time for approximately 3 seconds when the fan is
switched off. An audible signal will sound as an
acknowledgement.
Switching off
Touch and hold the
#
and
y
symbols at the same
time for approximately 3 seconds when the fan is
switched off. An audible signal will sound as an
acknowledgement.
2
Cleaning and maintenance
Cleaning and maintenance
:
Warning – Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
:
Warning
Risk of electric shock!
■
Penetrating moisture may result in an electric shock.
Clean the appliance using a damp cloth only. Before
cleaning, pull out the mains plug or switch off the
circuit breaker in the fuse box.
Risk of electric shock!
■
Do not use any high-pressure cleaners or steam
cleaners, which can result in an electric shock.
:
Warning – Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
Caution!
There is a risk of surface damage if you do not peel off
the protective film.Remove the protective film from all
parts of the appliance before using the appliance for the
first time.
Cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning product, follow the
instructions in the table. Do not use any of the following:
■
Harsh or abrasive cleaning agents, e.g. scouring
powder or liquid scouring cleaner,
■
Cleaning products with a high alcohol content,
■
Hard scouring pads or cleaning sponges,
■
Pressure washers or steam cleaners,
■
Cleaning products that dissolve limescale,
■
Aggressive all-purpose cleaning products,
■
Oven spray.
Note:
Wash new sponge cloths thoroughly before use.
Note:
Follow all instructions and warnings included with
the cleaning products.
Cleaning and maintenance
en
11
--------
Removing metal grease filter
1.
Open the lock and swing down the metal grease
filter. When you do this, take hold of the metal
grease filter from underneath with your other hand.
2.
Take the metal grease filter out of the holder.
Notes
– Fat may accumulate in the bottom of the metal
grease filter.
– Hold the metal grease filter level to prevent fat
from dripping out.
Cleaning the metal mesh grease filters
These instructions apply to several appliance variants. It
is possible that individual features are described which
do not apply to your appliance.
:
Warning – Risk of fire!
Fatty deposits in the grease filter may catch fire.
Regularly clean the grease filter. Never operate the
appliance without a grease filter.
Notes
■
Do not use aggressive, acidic or alkaline cleaning
products.
■
We recommend cleaning the grease filters every 2
months.
■
When cleaning the metal grease filters, also clean
the metal grease filter holder in the appliance using
a damp cloth.
■
The metal grease filters can be cleaned in the
dishwasher or by hand.
By hand:
Note:
You can use a special degreaser to remove
stubborn dirt. This can be ordered from the online shop.
■
Soak the metal grease filters in hot soapy water.
■
Clean the filters with a brush and then rinse them
thoroughly.
■
Leave the metal grease filters to drain on an
absorbent material.
In the dishwasher:
Note:
Slight discolouration may occur if the metal
grease filters are cleaned in the dishwasher. This
discolouration has no effect on the performance of the
metal grease filters.
■
Use normal domestic dishwashing detergents.
■
Do not clean heavily soiled metal grease filters
together with cookware.
■
Place the metal grease filters in the dishwasher,
leaving plenty of space around them. Do not trap the
metal grease filters.
■
Select a temperature of no more than 70 °C.
Area
Cleaning products
Stainless steel
Hot soapy water:
Clean with a dish cloth and then dry with a
soft cloth.
Clean stainless steel surfaces in the direction
of the grain only.
Special stainless steel cleaning products are
available from our after-sales service or from
specialist retailers.Apply a very thin layer of
the cleaning product with a soft cloth.
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and then dry
with a soft cloth.
Do not use stainless steel cleaner.
Aluminium and plastic Hot soapy water:
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Controls
Hot soapy water:
Clean using a damp dish cloth and then dry
with a soft cloth.
Risk of electric shock caused by penetrating
moisture.
Risk of damage to the electronics caused by
penetrating moisture. Never clean controls
with a wet cloth.
Do not use stainless steel cleaner.
Содержание DWB98JQ50B
Страница 2: ......
