background image

Bosch Security Systems | 2004-11 

DVR1A1081

 | Installation Manual | Chapter 1

EN

 | 5

1

SAFETY  PRECAUTIONS

1.1 IMPORTANT SAFEGUARDS

1. Please read these safety instructions carefully.
2. Please keep this User's Manual for later reference.
3. Please disconnect this equipment from connecter 

before cleaning.  Don't use liquid or sprayed 
detergent for cleaning.  Use moisture sheet or cloth 
for cleaning.

4. Make sure the voltage of the power source when 

connect the equipment to the power outlet.

5. All cautions and warnings on the equipment should 

be noted.

6. Never pour any liquid into opening, this could cause 

fire or electrical shock.

7. Never open the equipment.  For safety reason, the 

equipment should only be opened by qualified 
service personnel.

8. If one of the following situations arises, get the 

equipment checked by a service personnel :
a. Liquid has penetrated into the equipment.

b. The equipment has been exposed to moisture.
c. The equipment has not work well or you can not 

get it work according to user's manual.

d. The equipment has dropped and damaged.
e. If the equipment has obvious sign of breakage.

9. Do not leave this equipment in an environment 

unconditioned, storage temperature above 

5

0°C, it 

may damage the equipment. 

10. Operation Ambient 

4

0°C

11. Power cords : Use the proper power cord with 

correct attachment plug type. If the power source is 
120 V AC, use a power cord that has UL and CSA 
approvals. If the power source is a 240 V AC supply, 
use the tandem (T blade) type attachment plug with 
ground conductor power cord that meets the 
respective European country's safety regulations, 
such as VDE for Germany. Plug need approval with 
VDE 0620, connector approval by VDE 0625, 
minimum 10A, power cord H05VV-F or VW-1,0.75 
mm2 x 3G should be used.

12.   

13. The back of the recorder should only be removed by 

qualified maintenance and service personnel.

14. Danger of explosion if battery is incorrectly 

replaced. A lithium battery is located inside the 
enclosure of this recorder. Replace only with the 
same or equivalent type. Dispose of the replaced 
battery in an environmentally friendly way.

15. Keep ventilation openings free to avoid the recorder 

for overheating.

16. Do not place the recorder in the immediate vicinity 

of a heating source.

17. Do not install this equipment in a confined space 

such as a bookcase or similar unit.

Cleaning

You can clean the unit with a moist fluff-free cloth or 
shammy leather cloth.

Bosch has a strong commitment towards the 
environment. This unit has been designed to respect the 
environment as much as possible.

Danger

The lightning flash with arrowhead symbol, 

within an equilateral triangle, is intended to alert 

the user to the presence of an uninsulated 

“dangerous voltage” within the product's 

enclosure that may be of sufficient magnitude to 

constitute a risk of electric shock to persons. 

Warning

The exclamation mark within an equilateral 

triangle is intended to alert the user to the 

presence of important operating and 

maintenance (servicing) instructions in the 

literature accompanying the appliance.

Caution

To reduce the risk of electric shock, do not 

remove cover (or back). No user-serviceable 

parts inside. Refer servicing to  qualified service 

personnel.

Warning

To reduce the risk of fire or electric shock, this 

apparatus should not be exposed to rain or 

moisture and objects filled with liquids,such as 

vases, should not be placed on this apparatus.

EazeoRecorderInstalA.book  Page 5  Tuesday, November 23, 2004  3:47 PM

Содержание DVR1A1081























Отзывы: