Bosch DS484Q, Руководство по установке

Страница: 11 / 20

DS484Q/DS486Q | Installation Instructions | 4.0 Setup and Alignment
.
Bosch Security Systems, Inc. | 7/05 | 4998138530F 11
4.1.2 Transmitter Setup
Figure 15: Transmitter Setup Switches
OUTDOOR
INDOOR
BEAM POWER CONTROL (m)
60
120
100
200
130
260 160
320
200
400
180
360
MODEL:DS486Q
SWITCH
OFF
↔
ON
No ITEM OFF ON
1 Group A B
2
3 SEE CHART
BELOW
4 NULL
- -
SW2 - 3 : CHANNEL
M
OFF
OFF SW2
SW3
1
OFF
ON
2
ON
OFF
3
ON
ON
POWER
1
2
1 - Beam Power Control rotary switch
2 - DIP Switches 1, 2, and 3
Turn the Beam Power Control rotary switch to the
volume setting for the appropriate detection range.
Refer to
Figure 15, Table 5 and Table 6 .
Table 5: Settings for Outdoor Beam Power
Control
DS484Q DS486Q
Volume
Setting
Range
m (ft)
Volume
Setting
Range
m (ft)
40 0 to 40
(0 to 131)
60 0 to 60
(0 to 197)
60 40 to 60
(131 to 197)
100 60 to 100
(197 to 328)
80 60 to 80
(197 to 263)
130 100 to 130
(328 to 427)
100 80 to 100
(263 to 328)
160 130 to 160
(427 to 525)
110 100 to 110
(328 to 361)
180 160 to 180
(525 to 591)
120 110 to 120
(361 to 394)
200 180 to 200
(591 to 656)
Table 6: Settings for Indoor Beam Power
Control
DS484Q DS486Q
Volume
Setting
Range
m (ft)
Volume
Setting
Range
m (ft)
80 0 to 80
(0 to 263)
120 0 to 120
(0 to 394)
120 40 to 120
(263 to 394)
200 120 to 200
(394 to 656)
160 120 to 160
(394 to 525)
260 200 to 260
(656 to 853)
200 160 to 200
(525 to 656)
320 260 to 320
(853 to 1050)
220 200 to 220
(656 to 722)
360 320 to 360
(1050 to 1181)
240 220 to 240
(722 to 787)
400 360 to 400
(1181 to 1312)
4.1.3 Beam Group and Channel Setup
When installing only one transmitter and
one receiver (a set), beam group and
channel selection is not required. Leave the
switches on the transmitter and receiver in
the original (OFF) positions. Refer to
Figure 17 on page 12.
The transmitter and the receiver have eight selectable
beams. The beams are divided into two groups
(Group A and Group B) of four beams each. The
beams are referred to as channels (Channels M, 1, 2,
and 3). Refer to
Figure 16 .
Figure 16: Beam Group and Channel
Organization
BEAM GROUP A CHANNEL M
CHANNEL 1
CHANNEL 2
CHANNEL 3
GROUP B CHANNEL M
CHANNEL 1
CHANNEL 2
CHANNEL 3
Channels 1, 2 or 3 can emit beams only when
Channel M in the same group provides those channels
with synchronized (synchro) wiring. Refer to
Section
4.1.4 Synchronized Wiring on page 12. When installing
two or more sets in the same group, set only the first
set to Channel M. Set the remaining sets to Channel 1,
2, or 3.