Bosch D340 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 24

background image

Duct smoke housing, 2-wire

Mounting | en

11

Bosch Security Systems, Inc.

Installation manual

2017.04 | 7.0 | F.01U.071.685

1

2

Figure 3.8: Foam gaskets

1 Sample/exhaust tube posts

2 Foam gaskets

7.

Mount the housing to the jack nuts using the supplied machine screws (see the following
figure). Remember that over‑tightening the screws can cause excessive bowing of the
duct.

Figure 3.9: Mounting the housing

1 Duct

2 Housing

3 Machine screws (supplied)

8.

Determine and remove the appropriate wire knockouts for power and for any remote
indicator wiring (see the following figure).

«
...
9
10
11
12
13
...
»

Содержание D340

























Отзывы:

Нет отзывов

Похожие инструкции для D340

Бренд: K-9 Страницы: 18

Prestige APS997Z

Бренд: Voxx Electronics Страницы: 2

Бренд: Sidewinder Страницы: 52

Бренд: Pur Line Страницы: 52

Prestige APS-25CH

Бренд: Audiovox Страницы: 8

Бренд: Vanderbilt Страницы: 5

Бренд: Bellman & Symfon Страницы: 27

Бренд: Datexx Страницы: 1

WILD WEST TRADITION 10201600

Бренд: oklahoma joes Страницы: 16

Wild West Tradition 09201554

Бренд: oklahoma joes Страницы: 16

Бренд: Ambient Weather Страницы: 17

Бренд: Black Widow Страницы: 4

Бренд: Masterbuilt Страницы: 24

Бренд: Abus Страницы: 80

Бренд: Kinger Home Страницы: 7

Бренд: BioBrite Страницы: 4

Бренд: Code Alarm Страницы: 33

Бренд: DEI Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды