Bosch C1050ES Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 72

background image

6 720 646 812

Appliance details

5

2

Appliance details

2.1

Features

Parts

• Key Pad interface control

• High power pre-mix compact burner with low NOx

emissions

• Modulating Gas Valve with constant gas:air ratio

control

• Modulating water valve for improved comfort and

temperature control.

High quality materials for long working life

• Copper heat exchanger

• High efficiency Ceramat Burner

• Compact space saver: mounts on a wall with a

supplied bracket.

Features

• Easily removable one-piece cover

• On/Off and Temperature control switches

• Reset button

• Program button (Selectable temperature default)

• Failure codes for easy diagnostics and repair

• Real-time diagnostics for troubleshooting/informa-

tional purposes

• Built in freeze prevention.

Note:

The freeze prevention kit is designed to provide

protection for the water heater down to approximately
5°F for short term conditions only. It will not protect the
appliance in areas where the temperature is routinely
expected to be below freezing.
- The freeze prevention kit will not protect plumbing out-
side the appliance from freezing. Precautions should be
taken.

Accessories (Bosch part #)

• Optional wireless remote control to operate with the

appliance (TSTAT2)

• Cascading kit (77090003962)

• Outdoor kit (BTOK)

• External water filter (part # 8 703 305 356)

• Concentric termination kit (196016)

• Exhaust/Intake bird screen (L2594)

• Condensate drain tee (196061) [included with Con-

centric termination kit]

• Pipe Cover (PTPCES)

• High temperature kit (7736500074)

• Recess box kit (7736500043)

• Pressure relief valve (FWL-2).

2.2

Specifications (Technical data)

Approved in US/Canada

Capacity

Maximum flow rate: 7.15 GPM (27 l/min) at a 45°F
(25°C) rise.

Maximum output

157,700 Btu/h (46.2 kW)

Maximum input

175,000 Btu/h (51.2 kW)

Efficiency in %

Thermal efficiency > 92%

Minimum Input

19,900 Btu/h (5.8 kW)

Temperature Control

Selection range: 100°F (38°C) - 140°F (60°C)

Default temperature: 122°F (50°C)

Stability: +/- 2°F (+/- 1°C)

Gas Requirement

Gas connection (inches) - ¾”

Inlet gas pressure under operation (with a high hot
water flow rate)*

• Propane: 8” - 13” water column

• Natural Gas: 3.5” - 10.5” water column.

* To measure Gas Pressure, see Measuring Gas
Pressure, chapter 3.14, page 35.

Water

• Hot water connection (inches) - ¾”

• Cold water connection (inches) - ¾”

• Water valve material: Polymer (PPS) (Polypropylene

Sulfid)

• Minimum water flow: 0.5 gallon/minute (1.9 l/m)

Note: Activation varies with inlet water temperatures
from 0.5 - 1.6 gallon/minute (1.9 - 6.1 l/m).

• Minimum recommended water pressure: 30 PSI

(2.07 bar)

• Minimum well pressure 40 psi, see page 29.

• Connections:

– Bottom of heater

Combustion

• NOx

≤

14 Ng/J

(Nanograms of NOx (calculated as NO2) per

Joule of heat output).

i

BOSCH is constantly improving its
products, therefore specifications are
subject to change without prior notice.

«
...
3
4
5
6
7
...
»

Содержание C1050ES









































































Отзывы:

Нет отзывов

Похожие инструкции для C1050ES

Бренд: Paradyne Страницы: 86

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 54

Бренд: T-Tech Страницы: 38

Бренд: 7AMEnfant Страницы: 2

Ergopower Record 12s

Бренд: CAMPAGNOLO Страницы: 124

Бренд: CAMPAGNOLO Страницы: 100

Бренд: Hanlong Страницы: 26

Бренд: Yakima Страницы: 11

WorkCentre Pro 123

Бренд: Xerox Страницы: 4

7500DX - Phaser Color LED Printer

Бренд: Xerox Страницы: 5

Бренд: Taffio Страницы: 8

Бренд: Axxess Страницы: 8

Бренд: Ikelite Страницы: 32

Бренд: REVCAMUK Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды