manualshive.com logo in svg

Bosch BSS250-21-2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Bosch BSS250-21-2 Скачать руководство пользователя страница 16

16 

 

 

 

 

 

 
INSTALLATION 

– STORAGE TANK 

 
COMPLIANCE WITH STANDARDS 

 
The installation must be performed by an Authorised Persons and comply with the 

requirements of AS/NZS 3500.4, AS/NZS 3000 in New Zealand NZBC G12 and all local codes 

and regulatory authority requirements.  It is recommended the solar storage tank be installed 

at ground or floor level. The water heater must stand vertically upright. 

SUITABILITY FOR INSTALLATION IN FROST AREAS 

 
The system is suitable for installation in areas that experience sub-zero temperatures; it has 

an air bleed valve freeze protection system integrated into the system to prevent damage in 

the event of a light frost.  Areas of known heavy frost or altitudes higher than 600 m above sea 

level are not suitable for this system. The minimum temperature these systems are suitable for 

in no lower than -5°C. 

NOTE: THIS WATER HEATER IS NOT SUITABLE FOR POOL HEATING. 

LOCATION 

 
Whether located outdoor or indoor, the solar water storage tank should be installed close to 

the most frequently used hot water outlet (typically the shower) and its position chosen with 

safety and service in mind. The panels should be located as close as possible to the storage 

tank. 

CLEARANCES 

 
Allow adequate room to work with tools. A minimum of 250mm clearance around the water 

heater is required. An additional 300mm is required for relief valve removal, 800mm for access 

cover removal and 400mm for element removal. You should be able to read the information on 

the rating plate and all informative labelling. 

Содержание BSS250-21-2





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды