Bosch ANGLE EXACT ION 8-1100, Оригинальное руководство пользователя

Страница: 16 / 249

16 | English
1 609 92A 0CL | (28.11.13) Bosch Power Tools
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.

Do not continue to press the On/Off switch after the
machine has been automatically switched off.
The bat-
tery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Removing the battery (see figures A1 – A2)
The battery 9 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button
10 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
– To remove the battery 9 , press the unlocking button 10
and pull out the battery toward the front. Do not exert any
force.
Battery Charge-control Indication (yellow LED)
Operating and Storage Environment
The device is suitable exclusively for operation at enclosed
work sites.
For proper operation, the allowable ambient temperature
should be between 0 °C und +45 °C at an allowable relative hu-
midity between 20 and 95 %, free of moisture condensation.
Suspension Device (see figure B)
With the utility clip 11 , the machine can be attached to a sus-
pension device.
– Fasten the utility clip 11 to the machine by engaging it into
the fastening slots 12 .

Regularly check the condition of the utility clip and the
hook of the suspension device.
Configuring the Power Tool
With the
BOSCH EXACT Configurator
software, different pow-
er tool settings (e. g., speed, driving stages, repeat protec-
tion) can be configured. For this, the power tool must be con-
nected to a PC via the USB data port.
Note: Observe all safety warnings and instructions in the soft-
ware instruction manual.
Changing the Tool (see figure C)

When working with an application tool, pay attention
that the application tool is firmly seated on the tool
holder.
When the application tool is not firmly connected
with the tool holder, it can come loose again and not be
controlled.
Inserting
Use only insertion tools with fitting end pieces
(1/4" hexagonal).
– Pull the sleeve of quick-change chuck 2 to the front and
hold.
– Insert tool bit 13 into tool holder 1 and release the quick-
change chuck.
Removing
– Pull the sleeve of quick-change chuck 2 to the front and
hold.
– Remove tool bit 13 from tool holder 1 and release the
quick-change chuck.
Operation

Before any work on the power tool, remove the battery.
Starting Operation
When starting the power tool, you should first select the di-
rection of rotation with the rotational direction switch
6 since
the power tool starts only when the rotational direction switch
6 is not in the middle position (switch-on lock).
Reversing the rotational direction (see figure D)
– Right rotation: For driving in screws, push the rotational
direction switch 6 left to the stop.
– Left Rotation: For loosening or unscrewing screws, push
the rotational direction switch 6 right to the stop.
Switching On the Worklight
The work area illumination 3 makes possible the lighting of
the screwing position for unfavorable light conditions. The
work area illumination
3 is switched on by lightly pressing the
on/off switch 5 . When the on/off switch is firmly pressed, the
power tool is switched on and the work area illumination con-
tinues to light.
Battery Charge-
control Indica-
tion 7 Meaning
Flashing light +
audio signal Battery Charging:
Only 6 –8 more screwdriving operations
possible.
Continuous light Capacity no longer sufficient for a new
screwdriving operation or the machine
was subject to overload:
The machine can no longer be switched
on.
– Remove the battery and replace with
a fully charged one.
Flashing light The machine is overheated and out of
operation:
– Before restarting the operation of the
machine, wait until the flashing auto-
matically stops after a short period.
OBJ_BUCH-1781-002.book Page 16 Thursday, November 28, 2013 11:14 AM