Bosch AMC-4W Скачать руководство пользователя страница 42

Страница: 42 / 54

Operating the AMC-4W

Access Controller AMC-4W

Installation Guide

Bosch Security Systems | V.3.1/2006-09

Push Display:

Description:

02.05 15:35:15

Current date and time

Mac 0010174C8A0C

MAC address

N AMC 7604-3210

Network name

I192.168.10.18

IP address of the AMC-4W

H0.0.0.0

IP address of the host

DHCP 1

DHCP
  - 1 = on
  - 0 = off

D192.168.10.1

IP address of the DNS server

Host: +

Host activity,
+ online
-

offline

6.2.

Configuring the Ethernet Interface

To configure the AMC-4W in a TCP/IP network environment use the Windows
tool

AmcIpConfig

provided in the tools directory on the provided CD-ROM.

The installation and usage of the software application to configure the
AMC-4W via Ethernet interface is described in an additional
document:

AmcIpConfig – Configuration Software for the AMC-4W

6.3.

Resetting the AMC-4W

When a problem occurs, first, try to fix the problem directly. If this does not
solve the problem, resetting the AMC-4W may help:

Insert the provided screwdriver into the hole as shown in figure 31

Push the reset button for at least three seconds.

The AMC-4W will be reset and reboots. You are back in the download
program.

Now it is possible to reconfigure the AMC-4W from the beginning.

If the problem still arises, please, call your local service.

Содержание AMC-4W























































Результаты поиска

Содержание AMC-4W

Отзывы:

Похожие инструкции для AMC-4W

Бренды по названию

Популярные бренды

Bosch AMC-4W, Руководство по установке

Результаты поиска

Содержание AMC-4W

Отзывы:

Похожие инструкции для AMC-4W

Бренды по названию

Популярные бренды