Bosch AMC-4W Скачать руководство пользователя страница 4

Страница: 4 / 54

Contents

Access Controller AMC-4W

Installation Guide

Bosch Security Systems | V.3.1/2006-09

5.12.

Connecting Analog Input Devices...................................................... 38

5.13.

Tamper Protection .............................................................................. 40

Operating the AMC-4W .................................................................. 41

6.1.

Status Display of the AMC-4W.......................................................... 41

6.2.

Configuring the Ethernet Interface ..................................................... 42

6.3.

Resetting the AMC-4W...................................................................... 42

Appendix ........................................................................................... 44

7.1.

Connecting Diagrams ......................................................................... 44

7.2.

Jumpers............................................................................................... 48

7.3.

Proprietary burglar alarm/access control power supply .............

Fehler!

Textmarke nicht definiert.

7.3.1.

Overview ......................................

Fehler! Textmarke nicht definiert.

7.3.2.

Power Supply Voltage Output Selections.....

Fehler! Textmarke nicht

definiert.

7.3.3.

LED Diagnostics ..........................

Fehler! Textmarke nicht definiert.

7.3.4.

Installation Instructions for the RK-AL600ULX-4CB6.............

Fehler!

Textmarke nicht definiert.

7.4.

Legend................................................................................................ 50

7.5.

Product declaration............................................................................. 51

7.6.

Listings and Approvals....................................................................... 51

7.6.1.

FCC Notice......................................................................................... 51

7.6.2.

UL Listing .......................................................................................... 51

7.6.3.

Safety.................................................................................................. 51

7.7.

Included in delivery............................................................................ 51

List of Figures ................................................................................... 52

Index .................................................................................................. 54

Содержание AMC-4W























































Результаты поиска

Содержание AMC-4W

Отзывы:

Похожие инструкции для AMC-4W

Бренды по названию

Популярные бренды

Bosch AMC-4W, Руководство по установке

Результаты поиска

Содержание AMC-4W

Отзывы:

Похожие инструкции для AMC-4W

Бренды по названию

Популярные бренды