![Bosch Advanced Aquatak 150 Скачать руководство пользователя страница 19](http://html.mh-extra.com/html/bosch/advanced-aquatak-150/advanced-aquatak-150_original-instructions-manual_48288019.webp)
Problem
Possible Cause
Corrective Action
Frozen
Wait for pump/water supply hose/accessory to
thaw
Motor stops
Fuse faulty / blown
Replace fuse
Wrong mains voltage
Check that mains voltage corresponds to specific-
ations on the model tag
Motor protector has activated
Allow to cool for 15 minutes
Fuses blow
Fuses incorrectly rated
Change to a mains supply higher than the pres-
sure washer amp consumption
Motor starts but no
pressure
Nozzle partly blocked
Clean nozzle
Motor “sounds” but
fails to start
Insufficient power supply
Check that the voltage of the mains power supply
line is the same as that on the plate.
Voltage loss due to use of extension cable
Check characteristics of extension cable
Appliance not used for a long period of time
Contact your Bosch Service Centre
Problems with TSS (Total Stop System) device
Contact your Bosch Service Centre
Pressure pulsating
Air in the inlet water supply hose/pump
Allow pressure washer to run with open spray
handle and nozzle at low pressure until regular
working pressure is obtained
Inadequate water supply
Check that the water supply corresponds to spe-
cifications. The minimum specification for the wa-
ter supply hose is 1/2" or 13 mm diameter
Water filter blocked
Clean water filter
Water supply hoses squeezed
Straighten out kinked water supply hoses
High pressure hose too long
Remove high pressure extension hose. Retry (ex-
tension hose max. 7 m)
Pressure too low, but
steady
Note: Several types of
accessory will normally
deliver a lower pres-
sure
Nozzle worn
Change the nozzle
Start/stop valve worn
Activate trigger five times in quick succession
Motor starts up but
with restricted or no
working pressure
No water supply
Connect water supply
Water filter clogged up
Clean the water filter
Nozzle clogged up
Clean nozzle
The pressure washer
starts irregularly by it-
self
Pump/ power gun leaky
Contact your Bosch Service Centre
Water leaks from ma-
chine
Leaking pump
A slight water leak is permissible; in case of ex-
cessive leak, contact Bosch Service Centre.
Maintenance and Servicing
Maintenance
u
Stop, remove plug from the power supply and discon-
nect from water supply.
Note:
To ensure long and reliable service, carry out the fol-
lowing maintenance regularly.
Regularly check for obvious defects such as loose fixings,
and worn or damaged components.
Check that covers and guards are undamaged and correctly
fitted. Carry out necessary maintenance or repairs before
using.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by a
customer service centre that is authorised to repair Bosch
power tools.
After use/Storage
Turn the main switch off and operate the trigger to drain the
water from the high pressure hose.
English |
19
Bosch Power Tools
F 016 L81 291 | (13.07.2018)
Содержание Advanced Aquatak 150
