Bosch ABS M4 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 54

Bosch ABS M4 Скачать руководство пользователя страница 14

Parts Overview Kit Clubsport

There are a few variants of the ABS M4 Kit Clubsport available:

Description

Part Number

ABS M4 Kit Clubsport (1 MBaud, DF11S) F 02U V01 289‐49
ABS M4 Kit Clubsport (500 kBaud,
DF11S)

F 02U V01 289‐48

ABS M4 Kit Clubsport (1 MBaud, for
DF11i)

F 02U V00 543‐13

ABS M4 Kit Clubsport (500 kBaud, for
DF11i)

F 02U V00 543‐12

ABS M4 Kit includes all parts from Kit 1, but a different wiring harness, which
cannot be modified. By default the wiring harness includes a 60 Ohm terminal re‐
sistance, which can be replaced customer specific by a 120 Ohm or deleted com‐
pletely, see wiring diagram ABS M4 Clubsport.

Description

Part Number

Wiring harness Clubsport

F 02U V01 917‐01

See also

2

Wiring Diagram ABS M4 Clubsport [

Connectors Overview Kit 1

ABS M4 Kit 1 with part number F 02U V00 289‐01 includes the following connec‐
tors, which are also available as individual spare parts:

Connector for

Part Number

Attached control unit connector

Standard
wire departure on top: F 02U B00
238‐01
wire departure on top 90°: F 02U B00
238‐01
Alternativ
wire departure on bottom: F 02U B00
237‐01
wire departure on bottom 90°: F 02U
B00 237‐01

Brake pressure sensor
Compact 3‐pin connector

D 261 205 335‐01

12‐positon ABS map switch
ASL 006‐05SE‐HE

F 02U 000 230‐01

ABS warning light (MIL)
ASL 006‐05SA‐HE

F 02U 000 226‐01

5.3

5.4

5 | Included in the Kit

14 / 54

ABS M4 Manual

Bosch Motorsport

«
...
12
13
14
15
16
...
»

Содержание ABS M4























































Отзывы:

Нет отзывов